Chapter 3 · Science

Electricity: Circuits and their Components

How a torch works, what cells, batteries, lamps, LEDs and switches do, how to join them in a circuit and draw it with symbols, and which materials let electric current pass through them.

Answers to all 11 questions under “Let us enhance our learning” at the end of the chapter. Each question is given exactly as it appears in the book.

Let us enhance our learning

Questions 1 to 11

  1. Q1
    Choose the incorrect statement.(i) A switch is the source of electric current in a circuit.(ii) A switch helps to complete or break the circuit.(iii) A switch helps us to use electricity as per our requirement.(iv) When the switch is in ‘OFF’ position, there is an air gap between its terminals.

    Answer

    (i) is incorrect.

    A switch does not make electricity. The cell (or battery) is the source of electric current. A switch only completes or breaks the circuit. Statements (ii), (iii) and (iv) are correct.

  2. Q2
    Observe Fig. 3.16. With which material connected between the ends A and B, the lamp will not glow?

    The book shows a circuit like the one below, with a gap between two ends, A and B.

    A cell and a lamp joined in a loop with a gap between two ends, A and B. A material can be joined between A and B.CellLampAB
    A circuit with a gap between A and B.

    Answer

    The lamp will not glow if an insulator is joined between A and B, for example a plastic scale, a rubber eraser, a piece of wood, glass, paper or cloth. Insulators do not let current pass, so the circuit stays open.

    If a conductor, such as an iron nail, a copper wire, aluminium foil or a steel spoon, is joined between A and B, the circuit is closed and the lamp glows.

  3. Q3
    In Fig. 3.17, if the filament of one of the lamps is broken, will the other glow? Justify your answer.

    The book shows two lamps joined one after the other with a cell, like this:

    A cell and two lamps joined one after another in a single loop, so there is only one path for the current.Lamp 1Lamp 2Cell
    Two lamps in one loop.

    Answer

    No, the other lamp will not glow.

    The two lamps are in one single path. A broken filament makes a gap in that path, so the circuit becomes open. No current can flow anywhere in the circuit, so the other lamp also goes off.

  4. Q4
    A student forgot to remove the insulator covering from the connecting wires while making a circuit. If the lamp and the cell are working properly, will the lamp glow?

    Answer

    No. The covering on a wire is made of plastic or rubber, which are insulators. If the covering is not removed at the ends, the metal of the wire does not touch the terminals of the cell and the lamp. The circuit is not complete, so no current flows and the lamp does not glow. The ends of the wires must be stripped bare before joining them.

  5. Q5
    Draw a circuit diagram for a simple torch using symbols for electric components.

    Answer

    Circuit diagram of a torch: a battery of two cells, a switch and a lamp joined in one loop. With the switch ON, current flows from the plus terminal through the switch and the lamp back to the minus terminal.Switch (ON)+−BatteryLamp
    Circuit diagram of a torch.

    A torch has a battery of two cells, a switch and a lamp, all joined in one loop. The cells are joined + to −. When the switch is ON, current flows from the + terminal, through the switch and the lamp, back to the − terminal.

  6. Q6
    In Fig. 3.18:(i) If S2 is in ‘ON’ position, S1 is in ‘OFF’ position, which lamp(s) will glow?(ii) If S2 is in ‘OFF’ position, S1 is in ‘ON’ position, which lamp(s) will glow?(iii) If S1 and S2 both are in ‘ON’ position, which lamp(s) will glow?(iv) If both S1 and S2 are in ‘OFF’ position, which lamp(s) will glow?
    Fig. 3.18 redrawn: one single loop. Along the top wire are lamp L1, switch S2 and lamp L2; along the bottom wire are switch S1 and a battery. There is only one path for the current.L1L2S2S1
    Fig. 3.18, redrawn.

    Answer

    Both lamps and both switches are in one single loop. There is only one path for the current, so it flows only when both switches are ON. If either switch is OFF, there is a gap in the loop and neither lamp glows.

    (i) Neither lamp glows, because S1 is OFF and breaks the loop.

    (ii) Neither lamp glows, because S2 is OFF and breaks the loop.

    (iii) Both L1 and L2 glow, because the loop is complete.

    (iv) Neither lamp glows, because the loop is broken in two places.

  7. Q7
    Vidyut has made the circuit as shown in Fig. 3.19. Even after closing the circuit, the lamp does not glow. What can be the possible reasons? List as many possible reasons as you can for this faulty operation. What will you do to find out why the lamp did not glow?

    The book shows Vidyut’s circuit: a cell, a lamp in a holder, and a switch made from a safety pin and two drawing pins on a board, joined by wires.

    Answer

    Possible reasons:

    • The cell is used up (dead).
    • The filament of the lamp is broken (the lamp has fused).
    • A wire is loose, or is not touching a terminal.
    • The plastic covering has not been removed from the ends of a wire.
    • A wire is broken inside its covering.
    • The safety pin of the switch is not touching both drawing pins, or a pin is rusty or dirty, so the switch does not close the gap even when it is ON.
    • The lamp is loose in its holder.
    • Both wires of the lamp are joined to the same terminal of the cell.

    How to find the fault: check one part at a time, changing only that part.

    1. Check that every joint is tight and that the bare metal ends touch the terminals.
    2. Replace the cell with a new one. If the lamp now glows, the old cell was dead.
    3. Replace the lamp with one that works. If it glows, the old lamp had fused. (Or look for a broken filament.)
    4. Replace the wires one at a time, and then the switch, to see if any of them is faulty. A conduction tester can also be used to check each wire and the switch.
  8. Q8
    In Fig. 3.20, in which case(s) the lamp/LED will not glow when the switch is closed?

    The book shows four circuits. In (a) and (b) a cell, a switch and a lamp are joined, with the cell the other way round in (b). In (c) and (d) a battery of two cells, a switch and an LED are joined, with the battery the other way round in (d). The LED points the same way in (c) and (d).

    Answer

    Only in case (c), the lamp/LED will not glow.

    • (a) and (b): a filament lamp glows whichever way round the cell is joined, so the lamp glows in both.
    • (c) and (d): an LED glows only when its + side (the wide end of the triangle) is joined towards the + terminal of the battery. In (d) the + terminal (the long line) is on the side of the LED’s + end, so it glows. In (c) the battery is the other way round, so the LED is joined back to front and does not glow.
  9. Q9
    Suppose the ‘+’ and ‘–’ symbols cannot be read on a battery. Suggest a method to identify the two terminals of this battery.

    Answer

    Use an LED, which glows only when it is joined the right way.

    1. Join the longer leg of the LED to one terminal of the battery and the shorter leg to the other terminal.
    2. If the LED glows, the terminal joined to the longer leg is the + terminal, and the other is the − terminal.
    3. If it does not glow, swap the legs. Now it should glow, and again the terminal at the longer leg is +.

    (A filament bulb cannot be used for this, because it glows either way round.)

  10. Q10
    You are given six cells marked A, B, C, D, E, and F. Some of these are working and some are not. Design an activity to identify which of them are working.(i) List the items that you require.(ii) Write the procedure that you will follow.(iii) With the items, carry out the activity to identify the cells that are working.

    Answer

    (i) Items: a lamp (torch bulb) in a lamp holder, a cell holder, two connecting wires with bare ends, and a switch (optional). Also one new cell, to check that the lamp works.

    (ii) Procedure:

    1. Make a circuit of the cell holder, the switch and the lamp.
    2. Put the new cell in the holder and close the switch. The lamp glows, so the lamp and wires are fine.
    3. Now put cell A in the holder, the right way round, and close the switch. Note whether the lamp glows.
    4. Repeat with cells B, C, D, E and F, one at a time, keeping everything else the same.

    (iii) Record the results in a table like this one:

    CellDoes the lamp glow?Working or not?
    AYes / NoWorking / Not working
    B
    C
    D
    E
    F

    The cells with which the lamp glows are working; the cells with which it does not glow are not working.

  11. Q11
    Using an LED that requires two cells in series to glow, Tanya made the circuit as shown in Fig. 3.21. Will the lamp glow? If not, draw the wires for correct connections.

    The book shows two cells lying side by side, both with the + end on the right. A wire joins the − end of one cell to the − end of the other. The + end of the top cell is joined to the − leg of the LED, and the + end of the bottom cell to the + leg.

    Answer

    No, the LED will not glow.

    The two cells are joined − to −, so they push the current in opposite directions and cancel each other out. They do not make a battery. (The LED’s legs are also both joined to + terminals.)

    For the LED to glow:

    • the two cells must be joined + of one to − of the other, to make a battery;
    • the free + terminal of the battery must go to the longer (+) leg of the LED;
    • the shorter (−) leg of the LED must go back to the free − terminal of the battery.
    The correct way to join an LED to two cells: the two cells are joined plus to minus to make a battery, the plus end of the battery goes to the longer, plus leg of the LED, and the shorter, minus leg goes back to the minus end of the battery.+−BatteryLED+ (longer leg)
    The correct connections for Tanya’s LED.