Chapter 3 · Science

Electricity: Circuits and their Components

How a torch works, what cells, batteries, lamps, LEDs and switches do, how to join them in a circuit and draw it with symbols, and which materials let electric current pass through them.

Done reading? Try the Circuit lab activity on this chapter.
In this chapter 8 topics
  1. 1A torch and its parts
  2. 2The electric cell and the battery
  3. 3Electric lamps: the bulb and the LED
  4. 4Making a lamp glow: the electric circuit
  5. 5The electric switch
  6. 6Circuit diagrams and symbols
  7. 7Conductors and insulators
  8. 8Using electricity safely

1A torch and its parts

When the lights go out at night, a torch is the first thing many of us reach for. Press its switch and it lights up. Press again and it goes dark. What is inside that makes this happen?

Inside a torch, cut open. Two cells lie end to end in the tube, the plus cap of one touching the minus end of the next, with a spring at the back. A brass metal strip runs from the back, past the switch on top, to the lamp. The lamp sits in a shiny reflector behind a glass cover.+−1.5 V+−1.5 VMetal stripSwitchReflectorSpringTwo cellsLampGlass
Figure 1. The main parts inside a torch.

Parts of a torch

PartWhat it does
CellsSupply the electricity. Most torches hold two or more cells placed end to end.
LampGives out light. It may be a small bulb or an LED.
SwitchTurns the torch on and off.
Metal strip and springJoin the cells, the switch and the lamp, so that electricity can travel between them.
ReflectorA shiny, curved surface behind the lamp. It sends the light forward in a beam.
Glass or plastic coverProtects the lamp and lets the light out.

Which way do the cells go?

Open a torch and look at the cells. Each cell has a raised metal cap at one end and a flat metal base at the other. Inside the torch, the cap of one cell touches the flat end of the next.

Now turn one cell the wrong way round and close the torch. The lamp does not light up. So the way you place the cells matters. You will see why in the next topic.

Remember

  • A torch has cells, a lamp, a switch, metal parts joining them, a reflector and a cover.
  • The cells give the electricity; the lamp gives the light; the switch turns it on and off.
  • The cells must be placed the right way round, cap to flat end.
Quick checkRahul puts the two cells of his torch in the wrong way round. What will happen when he presses the switch?Show answer

The lamp will not light up. The cells must be placed so that the cap of one touches the flat end of the next.

2The electric cell and the battery

A torch, a wall clock, a TV remote and many toys all run on small electric cells. A cell is a source of electricity, which means it is where the electricity comes from. It supplies the electricity that makes a lamp glow or a toy car move.

Left: an electric cell marked 1.5 V. Its positive terminal is the metal cap at one end; its negative terminal is the flat metal base at the other end. Right: a battery of two cells placed end to end, with the plus cap of one cell touching the minus end of the next.+−1.5 VPositive (+) terminalmetal capNegative (−) terminalflat metal baseAn electric cell+−+−+ of one cell touches− of the nextA battery of two cells
Figure 2. An electric cell has two terminals. A battery is made by joining cells.

Terminals of a cell

Every cell has two ends called terminals. The metal cap is the positive (+) terminal. The flat metal base is the negative (−) terminal. The + and − signs are printed on the cell.

Cells also have a number such as 1.5 V printed on them. V stands for volts. This number tells us how strongly the cell can push electricity around. You will learn more about it in higher classes.

A cell has chemicals inside it, and it makes electricity from them. When the chemicals are used up, the cell stops working. Then it must be replaced. Some cells, like the one in a mobile phone, can be charged again. Most small cells, like those in a TV remote, cannot.

Battery

Battery

Two or more cells joined together form a battery. To make a battery, join the + terminal of one cell to the − terminal of the next.

In a torch, the cells sit end to end in the tube, cap to base. So they form a battery. Now you can see why the cells must face the same way: the + of one must touch the − of the next.

Some devices, like a TV remote, hold the cells side by side in a cell holder. Inside the holder, a metal strip joins the + of one cell to the − of the next.

Why join cells at all? A battery gives a stronger push than a single cell. So we use one when one cell is not enough.

In everyday speech, people often call a single cell a “battery”. In science, a battery means two or more cells joined together.

Never cut open or burn a used cell. The chemicals inside can be harmful. Hand old cells in at a collection point instead of throwing them in the dustbin.

Remember

  • A cell is a source of electricity.
  • The metal cap is the + terminal; the flat base is the − terminal.
  • A battery is two or more cells joined, + of one to − of the next.
Quick checkShabnam has two cells. How should she join them to make a battery?Show answer

She should join the positive (+) terminal of one cell to the negative (−) terminal of the other.

3Electric lamps: the bulb and the LED

The part of a torch that gives light is called the lamp. Two kinds are common: the incandescent lamp (the ordinary bulb) and the LED. “Incandescent” means glowing because it is very hot.

Left: an incandescent bulb. A thin coiled filament inside a glass bulb is held up by two support wires. One wire is joined to the metal case of the base, which is one terminal; the other is joined to the metal tip at the bottom, which is the other terminal. Right: a red LED with two legs. The longer leg is the positive terminal and the shorter leg is the negative terminal.Incandescent lamp (bulb)FilamentGlassSupport wiresTerminal 1: metal caseTerminal 2: metal tipLEDLonger leg+ terminalShorter leg− terminal
Figure 3. An incandescent bulb and an LED. Each has two terminals.

Incandescent lamp

Look closely at a torch bulb. Inside the glass is a very thin, coiled wire called the filament. Two thicker wires hold the filament up.

  • One thick wire is joined to the metal case of the base.
  • The other is joined to the metal tip at the bottom.

The metal case and the metal tip are the two terminals of the bulb. Electricity goes in through one, passes through the filament, and comes out through the other. The filament gets so hot that it glows and gives out light. (A toaster wire glowing red is a similar idea.)

If the filament breaks, there is a gap inside the bulb. Electricity cannot cross the gap, so the bulb does not glow. We say the bulb has fused.

LED

LED stands for light emitting diode. “Emitting” means giving out. It has two wires, called legs. The longer leg is the + terminal. The shorter leg is the − terminal.

An LED is fussy about direction. It glows only when:

  • its + leg (longer) is joined towards the + terminal of the cell or battery, and
  • its − leg (shorter) is joined towards the − terminal.

Joined the other way round, it does not glow. A filament bulb is different: it glows whichever way round you join it. Many LEDs need two cells to glow brightly.

Incandescent lampLED
How it makes lightFilament gets very hot and glowsGives out light without getting very hot
Which way to joinEither way+ leg to the + side only
Electricity usedMoreMuch less
LifeShorterMuch longer
ColoursMostly yellowish whiteRed, green, blue, white and more

LEDs use much less electricity and last much longer. So today we use them almost everywhere: in homes, street lights, torches, traffic lights and screens.

Remember

  • A bulb has a filament that glows when electricity passes through it.
  • A bulb has two terminals: the metal case and the metal tip.
  • The longer leg of an LED is its + terminal; an LED glows only when joined the right way.
  • LEDs use less electricity and last longer than filament bulbs.
Quick checkWhy does a fused bulb not glow even with a new cell?Show answer

Its filament is broken, so there is a gap inside the bulb. Electricity cannot pass through the gap, so the bulb cannot glow.

4Making a lamp glow: the electric circuit

To make a lamp glow, we join it to a cell with connecting wires. A cell holder and a lamp holder keep the wires pressed firmly against the terminals.

A cell in a cell holder on a table is joined by two connecting wires to a lamp in a lamp holder. The lamp glows. Orange arrows show the current leaving the plus end of the cell, passing through the lamp and returning to the minus end.+−CurrentCell in a cell holderLamp in a lamp holderConnecting wire
Figure 4. A cell and a lamp joined by wires. The arrows show the direction of the current.
  1. Join one wire from the + terminal of the cell to one terminal of the lamp.
  2. Join a second wire from the other terminal of the lamp back to the − terminal of the cell.
  3. Now there is a complete path, like a running track with no break. The lamp glows.

Electric circuit

An electric circuit is a complete, closed path for electricity. The electricity flows from the + terminal of the cell, through the wires and the lamp, and back to the − terminal.

The flow of electricity in a circuit is called electric current. Scientists have agreed to show the current flowing from the + terminal of the cell, round the circuit, to the − terminal. Everyone uses the same direction, so diagrams are easy to share.

The parts joined in a circuit, such as cells, lamps, switches and wires, are called its components.

Closed and open circuits

  • If the path is complete, the circuit is closed. Current flows and the lamp glows.
  • If there is a break anywhere, the circuit is open. The break may be a loose wire, a broken filament or a gap. No current flows anywhere in the circuit, and the lamp does not glow.

Think of a line of children passing a ball around a circle. If one child steps out, the ball stops everywhere, not just at the gap.

What if both wires from the lamp go to the same terminal of the cell? Then the path never passes through the cell from + to −. So no current flows, and the lamp stays dark. A lamp needs one terminal joined to the + side and the other joined to the − side.

Remember

  • An electric circuit is a closed path from the + terminal, through the components, back to the − terminal.
  • Current flows only in a closed circuit.
  • Any break makes the circuit open, and the lamp goes off.
Quick checkPriya joins both wires of a lamp to the + terminal of a cell. Will the lamp glow? Why?Show answer

No. There is no complete path from the + terminal through the lamp back to the − terminal, so no current flows.

5The electric switch

We do not want to pull out a wire every time we turn a lamp off. A switch does this job for us.

Switch

A switch is a device that completes or breaks a circuit. It lets us use electricity only when we need it. A switch does not make electricity.

Left: the switch is OFF, so there is a gap in the circuit and the lamp does not glow. Right: the switch is ON, the circuit is complete, current flows round it and the lamp glows.Switch OFFSwitch ONOpen circuit: lamp offClosed circuit: lamp glows
Figure 5. A switch breaks the circuit when OFF and completes it when ON.
  • When the switch is ON, a piece of metal joins its two terminals. The circuit is closed, and the lamp glows.
  • When the switch is OFF, there is an air gap between its terminals. Air does not let current pass. So the circuit is open, and the lamp goes off.

A switch works like a drawbridge. When the bridge is down, traffic can cross. When it is up, nothing gets across.

Make your own switch

  1. Press two drawing pins into a piece of thick cardboard or wood, a little apart.
  2. Wind a bare wire end around each pin.
  3. Fix a metal strip, such as a safety pin or a paper clip, under one pin. It should be able to turn.
  4. Turn the strip until it touches the second pin. The switch is ON.
  5. Turn it away from the second pin. The switch is OFF.
A home-made switch: two brass drawing pins on a wooden board, each joined to a wire, and a metal strip that turns about one pin. Left, OFF: the strip is turned away, leaving an air gap between it and the second pin. Right, ON: the strip lies across both pins and joins them.OFF: openON: closedAir gapMetal stripDrawing pins joined to wiresStrip touches both pins
Figure 6. A home-made switch, OFF and ON.

You can put this switch anywhere in a circuit of a cell and a lamp. It can go before the lamp, after it, or next to the cell. Wherever it is, it turns the lamp on and off. This is because opening the circuit at any point stops the current everywhere.

Remember

  • A switch completes (ON) or breaks (OFF) a circuit.
  • In the OFF position there is an air gap between the terminals.
  • A switch can be placed anywhere in a simple circuit.
Quick checkIs a switch a source of electricity? Explain.Show answer

No. A switch only opens or closes the path. The cell is the source of electricity.

6Circuit diagrams and symbols

Drawing a real cell, wire and lamp every time takes a lot of effort. Also, different people would draw them differently. So scientists use simple symbols for the parts of a circuit. A symbol is a simple sign that stands for something, like the signs on road boards. Circuit symbols are understood everywhere in the world.

  • Electric cellThe longer line is the + terminal; the shorter, thicker line is the − terminal.
  • BatteryTwo or more cell symbols joined, + of one to − of the next.
  • Lamp (bulb)Glows when current flows through it.
  • LEDThe triangle points from + to −. The arrows show light given out.
  • Switch OFFOpen: there is a gap, so no current flows.
  • Switch ONClosed: the path is complete.
  • Connecting wireDrawn as a straight line.
Figure 7. Symbols for the components of a circuit.

Circuit diagram

A drawing of a circuit made with these symbols is called a circuit diagram.

In the cell symbol, remember: long line, + terminal; short thick line, − terminal.

In the LED symbol, look at the triangle. Its wide end is the + side. Its tip, with a short bar across it, is the − side. The triangle points the way the current flows.

The circuit diagram of a cell, a closed switch and a lamp joined in a loop. The lamp glows. Arrows show the current flowing from the plus terminal of the cell, through the switch and the lamp, back to the minus terminal.Switch (closed)+−CellLampCurrent
Figure 8. The circuit diagram of a cell, a switch and a lamp. The current flows from + round to −.
Two circuit diagrams. Left: a cell, a closed switch and a lamp. Right: a battery of two cells, a closed switch and an LED, with the plus side of the LED joined towards the plus terminal of the battery.Switch+−CellSwitch+−BatteryCell, switch and lampBattery, switch and LED
Figure 9. Circuit diagrams with a lamp and with an LED. The LED’s + side faces the + terminal of the battery.

Tips for drawing circuit diagrams

  • Draw wires as straight lines with square corners. Use a ruler.
  • Make sure the path is a closed loop with no gaps (unless you mean to show an open switch).
  • Show the + and − terminals of the cell clearly, especially when there is an LED in the circuit.

Remember

  • A circuit diagram uses standard symbols for the parts of a circuit.
  • In a cell symbol, the long line is + and the short thick line is −.
  • For a battery, draw cell symbols joined + to −.
Quick checkIn a cell symbol, which line stands for the positive terminal?Show answer

The longer, thinner line is the positive (+) terminal. The shorter, thicker line is the negative (−) terminal.

7Conductors and insulators

Does electricity pass through every material? You can find out with a simple conduction tester. (To conduct means to let something pass through.)

A conduction tester: a cell in a holder and a lamp in a holder are joined by wires, leaving two free wire ends. The material to be tested, here an iron nail, is placed so that it touches both free ends. The lamp glows, so iron is a conductor.+−Material being tested (an iron nail)CellLampFree ends
Figure 10. A conduction tester. The material is placed so that it touches both free ends.

Making and using a tester

  1. Join a cell and a lamp in a circuit, but leave a gap in one wire. You now have two free, bare wire ends.
  2. Touch the two ends together. The lamp should glow. This shows the tester works.
  3. Place a material so that it touches both ends, and watch the lamp.
  4. If the lamp glows, current is passing through the material. If not, the material is stopping the current.

Conductors and insulators

Materials that let electric current pass through them are conductors of electricity. Materials that do not let current pass through them are insulators.

Lamp glows (conductors)Lamp does not glow (insulators)
Iron nail, steel spoonPlastic scale, plastic comb
Copper wire, brass keyRubber eraser, rubber band
Aluminium foilWood, cork
Pencil lead (graphite)Glass, paper, cloth, thread

All metals are conductors. Graphite, the black “lead” of a pencil, is not a metal, but it also conducts. Dry air is an insulator. That is why the air gap in an OFF switch stops the current.

Conductors and insulators at work

  • A connecting wire has metal inside, usually copper, to carry the current. Outside, it has a covering of plastic or rubber, so that it is safe to touch.
  • Before you join wires, you must strip the plastic off the ends. Plastic is an insulator, so no current can pass through a covered end.
  • Switches, plugs and sockets have metal parts inside and plastic covers outside.
  • Electricians’ screwdrivers and pliers have plastic or rubber handles. These stop current from reaching their hands.

Remember

  • Conductors let current pass: metals and graphite.
  • Insulators do not: plastic, rubber, wood, glass, paper, dry air.
  • Wires are metal inside and plastic outside.
Quick checkA girl places a coin between the ends of her tester and the lamp glows. Then she places an eraser and the lamp does not glow. What can she conclude?Show answer

The coin is a conductor (it is metal), and the eraser is an insulator (it is rubber or plastic).

Try it yourselfSwitch the circuit on and off, add cells, and test which materials let current through in the circuit lab.

8Using electricity safely

The cells we use in activities are safe to handle. The electricity from the wall sockets in our homes is called the mains. It is far stronger than a cell. It can give a severe shock that can injure or even kill.

Never do any experiment with electricity from a wall socket, a generator or an inverter. (An inverter is the backup box that gives power during a power cut.) Use only cells for your activities.

Stay safe

  • Never put anything into a socket.
  • Do not touch switches, plugs or appliances with wet hands. Water from taps, wells and rain conducts electricity. So does the human body.
  • Do not use wires whose plastic covering is cut or worn out. Tell an adult to replace them.
  • Keep away from fallen electric wires, electric poles and transformers (the large metal boxes on poles or fenced platforms).
  • Do not fly kites near overhead wires.
  • Pull a plug out by holding the plug, not the wire.
  • If someone gets a shock, do not touch them. Switch off the main supply, or push the wire away with a dry wooden stick. Call an adult at once.

Remember

  • Experiment only with cells, never with the mains.
  • Wet hands and damaged wires are dangerous.
  • Rubber, plastic and dry wood are insulators that help keep us safe.
Quick checkA live wire is one that is carrying current. Why should you push it away from a person with a dry wooden stick, not a metal rod?Show answer

Dry wood is an insulator, so current will not pass through it to you. A metal rod is a conductor, so you would get a shock too.

Test yourselfTake the 16-question practice quiz on this chapter.