Chapter 5 · Chemistry

Exploring Mixtures and their Separation

How mixtures are classified and separated: homogeneous and heterogeneous mixtures, solutions and their concentration as a percentage, solubility and solubility curves, crystallisation, distillation, paper chromatography, separating immiscible liquids, sublimation, alloys, suspensions, centrifugation, coagulation, colloids and the Tyndall effect.

Questions on the ideas that come up most often in school tests and exams, in the same formats as CBSE papers. Each question shows the skill it tests. Try each one before you open the answer.

What school exams ask most

How this chapter is tested

  • Exploring Mixtures and their Separation is the first chemistry chapter of Class 9. Most papers have a numerical on percentage concentration and a question on choosing a separation method.
  • The ideas asked most often are: homogeneous and heterogeneous mixtures; the three percentage concentrations; solubility and solubility curves; crystallisation; distillation and fractional distillation; paper chromatography; the separating funnel; sublimation; centrifugation and coagulation; and solutions, suspensions and colloids with the Tyndall effect.
  • It is tested through multiple-choice and assertion–reason questions on definitions, 2 and 3-mark numericals and reasons, case-based questions with a table of solubilities, and long answers with a labelled diagram of an apparatus.
  • Marks are lost for dividing by the mass of the solvent instead of the solution, for calling milk or brass the wrong kind of mixture, for unlabelled diagrams, for putting the chromatography spot below the solvent, and for confusing sublimation with evaporation.

Asked most often, with questions to practise

  1. Kinds of mixturesQ1Q10Q22Q30
  2. Percentage concentrationQ2Q15Q20
  3. Solubility and crystallisationQ3Q11Q14Q18Q26
  4. Distillation and chromatographyQ4Q12Q24Q29
  5. Separating funnel, sublimation and other methodsQ5Q9Q16Q21Q23Q31
  6. Suspensions, colloids and the Tyndall effectQ6Q7Q8Q13Q17Q19Q25Q27Q28

1 mark each

Multiple choice questions

  1. Q1
    UnderstandingWhich of the following is a heterogeneous mixture?(a) air(b) brass(c) milk(d) sugar solution
    Show answer

    (c) milk

    Milk is a colloid, which is a heterogeneous mixture even though it looks uniform. Air, brass and sugar solution are homogeneous.

  2. Q2
    Application25 g of glucose is dissolved in water to make 500 mL of solution. Its concentration is(a) 5 % m/v(b) 20 % m/v(c) 2.5 % m/v(d) 0.5 % m/v
    Show answer

    (a) 5 % m/v

    percentage=25 g500 mL × 100=5 % m/v
  3. Q3
    UnderstandingThe method used to obtain pure crystals of alum from an impure sample is(a) evaporation(b) crystallisation(c) distillation(d) sublimation
    Show answer

    (b) crystallisation

    Soluble impurities stay behind in the solution while pure crystals form on cooling.

  4. Q4
    ApplicationWhich pair of liquids can be separated by simple distillation?(a) alcohol (78 °C) and benzene (80 °C)(b) acetone (56 °C) and alcohol (78 °C)(c) acetone (56 °C) and water (100 °C)(d) chloroform (61 °C) and alcohol (78 °C)
    Show answer

    (c) acetone (56 °C) and water (100 °C)

    Only this pair differs by more than 25 °C (by 44 °C). The others differ by 2 °C, 22 °C and 17 °C.

  5. Q5
    UnderstandingAmmonium chloride can be separated from common salt by(a) filtration(b) sublimation(c) distillation(d) a separating funnel
    Show answer

    (b) sublimation

    Ammonium chloride changes directly from solid to vapour on heating; common salt does not.

  6. Q6
    UnderstandingThe particle size in a colloid is(a) less than 1 nm(b) 1 nm to 1000 nm(c) more than 1000 nm(d) more than 1 mm
    Show answer

    (b) 1 nm to 1000 nm

    Solutions have particles smaller than 1 nm; suspensions have particles larger than 1000 nm.

  7. Q7
    Analytical thinkingA mixture shows the Tyndall effect, does not settle on standing and passes through filter paper. It is(a) a solution(b) a suspension(c) a colloid(d) an alloy
    Show answer

    (c) a colloid

    Scattering of light rules out a solution; not settling and passing through the filter rule out a suspension.

  8. Q8
    UnderstandingIn the dairy industry, cream is separated from milk by(a) coagulation(b) centrifugation(c) decantation(d) chromatography
    Show answer

    (b) centrifugation

    Spinning separates the lighter cream from the heavier skimmed milk.

1 mark each

Assertion–reason questions

Each question has two statements: an Assertion (A) and a Reason (R). Choose the correct option:

  1. (a)Both A and R are true, and R is the correct explanation of A.
  2. (b)Both A and R are true, but R is not the correct explanation of A.
  3. (c)A is true, but R is false.
  4. (d)A is false, but R is true.
  1. Q9
    UnderstandingAssertion (A): A mixture of oil and water can be separated using a separating funnel.Reason (R): Oil and water are immiscible liquids with different densities.
    Show answer

    (a) Both A and R are true, and R is the correct explanation of A.

    Because they do not mix and differ in density, they form two layers, and the lower one can be run off.

  2. Q10
    UnderstandingAssertion (A): An alloy can be separated into its components by physical methods.Reason (R): An alloy is a homogeneous mixture.
    Show answer

    (d) A is false, but R is true.

    An alloy is homogeneous (R is true), but its parts cannot be separated by physical methods, so A is false.

  3. Q11
    ApplicationAssertion (A): Crystals of copper sulphate are large and well shaped when a hot saturated solution is cooled slowly.Reason (R): The solubility of copper sulphate in water increases with temperature.
    Show answer

    (b) Both A and R are true, but R is not the correct explanation of A.

    Both are true. Solubility changing with temperature is why crystals form at all; the large size is due to slow cooling, which gives the particles time to arrange themselves. So R does not explain A.

  4. Q12
    UnderstandingAssertion (A): In paper chromatography, the sample spot must be kept above the level of the solvent.Reason (R): The solvent must carry the components up the paper, not wash them into the jar.
    Show answer

    (a) Both A and R are true, and R is the correct explanation of A.

    If the spot were below the solvent level, it would dissolve into the solvent instead of moving up the paper.

  5. Q13
    Analytical thinkingAssertion (A): Muddy water becomes clear when alum is added and it is left to stand.Reason (R): Alum dissolves the mud particles.
    Show answer

    (c) A is true, but R is false.

    A is true, but alum does not dissolve the mud: it makes the fine particles clump together (coagulation) so that they settle.

2 marks each

Very short answer questions

  1. Q14
    UnderstandingDefine solubility. How does the solubility of (i) a solid and (ii) a gas in water change with a rise in temperature?
    Show answer

    Solubility is the largest amount of a solute that can dissolve in a fixed amount of solvent (usually 100 g of water) at a given temperature.

    • (i) For most solids it increases.
    • (ii) For gases it decreases.
  2. Q15
    ApplicationA 200 g sample of a talcum powder contains 3 % m/m of an antiseptic. Find the mass of the antiseptic and of the rest of the powder.
    Show answer
    antiseptic=3100 × 200 g=6 grest=200 g − 6 g=194 g
  3. Q16
    UnderstandingGive two differences between sublimation and evaporation.
    Show answer
    SublimationEvaporation
    Change of stateSolid → vapour directlyLiquid → vapour
    Use in separationA solid that sublimes from one that does notA dissolved solid from its solvent
  4. Q17
    UnderstandingWhat is an emulsion? Give one example each of an oil-in-water and a water-in-oil emulsion.
    Show answer

    An emulsion is a colloid in which both the dispersed phase and the dispersion medium are liquids, such as oil and water.

    • Oil-in-water: milk (or vanishing cream).
    • Water-in-oil: butter (or cold cream).
  5. Q18
    ApplicationWhy is common salt obtained from seawater by evaporation and not by cooling a saturated solution?
    Show answer

    The solubility of common salt hardly changes with temperature (about 36 g at 10 °C and 37 g at 80 °C per 100 g of water). Cooling a saturated solution would give almost no crystals. Removing the water by evaporation leaves the salt behind.

  6. Q19
    UnderstandingState the principle of (i) centrifugation and (ii) coagulation.
    Show answer
    • (i) Centrifugation: when a mixture is spun very fast, the heavier particles are pushed outwards and settle at the bottom of the tube; the lighter liquid stays on top.
    • (ii) Coagulation: a coagulant such as alum makes very fine suspended particles clump together into larger lumps that settle under gravity.

3 marks each

Short answer questions

  1. Q20
    ApplicationRohan dissolves 12 g of sugar in 108 g of water, and Meera dissolves 15 g of sugar in 135 g of water. (i) Find the % m/m of each solution. (ii) Whose solution is sweeter? (iii) How much more water must Rohan add to make his solution 8 % m/m?
    Show answer
    Rohan=12 g12 g + 108 g × 100=12 g120 g × 100=10 % m/mMeera=15 g15 g + 135 g × 100=15 g150 g × 100=10 % m/m

    (ii) Both are equally sweet: each is 10 % m/m.

    (iii) At 8 % m/m, 12 g of sugar must be 8% of the solution:

    mass of solution=12 g8 × 100=150 gwater to add=150 g − 120 g=30 g
  2. Q21
    UnderstandingDraw a labelled diagram of the apparatus used to separate camphor from sand. Name the process and explain how it works.
    Show answer
    Sublimation of camphor. A china dish holding a mixture of camphor and sand is heated gently on a wire gauze. An inverted glass funnel with a cotton plug in its stem covers the dish. Camphor turns to vapour and deposits as a white solid on the cool inner wall of the funnel; the sand stays in the dish.Cotton plugGlass funnelCamphor depositsChina dishCamphor and sandWire gauzeBurner
    Separating camphor from sand by sublimation.

    The process is sublimation. On gentle heating, camphor changes directly into vapour without melting. The vapour deposits as solid camphor on the cool inner wall of the inverted funnel (deposition). Sand does not sublime and stays in the china dish.

  3. Q22
    Analytical thinkingA student says: “Milk looks the same throughout, so it is a homogeneous mixture.” Is she right? Give two observations that would help her decide.
    Show answer

    No. Milk is a colloid, which is heterogeneous, although it looks uniform.

    • A beam of light through diluted milk is visible from the side (Tyndall effect); it would not be in a true solution.
    • Under a microscope, tiny fat droplets can be seen spread through the liquid.
    • Spinning milk in a centrifuge separates the cream: a true solution cannot be separated this way.
  4. Q23
    UnderstandingHow would you separate a mixture of chalk powder, common salt and iron filings? Write the steps in order and the property used at each step.
    Show answer
    1. Magnet: move a magnet over the dry mixture to pick up the iron filings. (Iron is magnetic.)
    2. Dissolve and filter: stir the rest in water and filter. Chalk stays on the filter paper. (Salt is soluble, chalk is not.)
    3. Evaporate: heat the filtrate until the water is gone, leaving the salt. (Water turns to vapour, salt does not.)
  5. Q24
    UnderstandingIn a distillation set-up, why is (i) the thermometer bulb kept near the side arm, (ii) cold water passed in at the lower end of the condenser, and (iii) the flask heated gently?
    Show answer
    • (i) To measure the temperature of the vapour going into the condenser, which tells which liquid is distilling.
    • (ii) So that the condenser jacket stays full of cold water and the vapour is cooled all along its length.
    • (iii) So that only the liquid with the lower boiling point vaporises, and the mixture does not boil over or bump.
  6. Q25
    ApplicationExplain why (i) a beam of headlights is visible on a foggy night, (ii) a salt solution does not settle on standing, and (iii) muddy water filtered through cloth may still look cloudy.
    Show answer
    • (i) Fog is a colloid of tiny water droplets in air. They scatter the light, making the beam visible (Tyndall effect).
    • (ii) Salt is dissolved as particles smaller than 1 nm, spread evenly; a solution is homogeneous and never settles.
    • (iii) The finest clay particles are smaller than the gaps in the cloth, so they pass through. Coagulation with alum or centrifugation is needed.

4 marks each

Case-based questions

  1. Q26
    Analytical thinkingRead the case and answer the questions.

    The solubility (in g per 100 g of water) of two salts at different temperatures is given below.

    Salt20 °C40 °C60 °C80 °C
    Salt X3060105165
    Salt Y35363738
    1. (i)Which salt’s solubility changes more with temperature?1 mark
    2. (ii)What mass of X saturates 50 g of water at 40 °C?1 mark
    3. (iii)A saturated solution of X in 100 g of water at 80 °C is cooled to 20 °C. What mass of crystals forms? Which method, cooling or evaporation, would you use to get crystals of Y? Why?2 marks
    4. OR
    5. (iii)Draw a rough solubility curve for X and use it to estimate its solubility at 50 °C.2 marks
    Show answer

    (i) Salt X: it rises from 30 g to 165 g, while Y rises by only 3 g.

    (ii) mass of X=60 g100 g × 50 g=30 g
    (iii) crystals=165 g − 30 g=135 g

    For Y, use evaporation: its solubility hardly changes with temperature, so cooling would give very few crystals.

    OR (iii): plotting 30, 60, 105 and 165 g against 20, 40, 60 and 80 °C gives a curve that gets steeper. Halfway between 60 g (40 °C) and 105 g (60 °C), and allowing for the upward curve, the solubility at 50 °C is about 80 g per 100 g of water (any value from about 78 g to 83 g read from a smooth curve is fine). It is a little less than the halfway value, 82.5 g, because the curve bends upwards.

  2. Q27
    ApplicationRead the case and answer the questions.

    In a hospital laboratory, a blood sample is spun in a machine. After a few minutes, it has separated into a pale yellow liquid on top, a thin whitish layer, and a dark red layer at the bottom. Blood is described as a colloid.

    1. (i)Name the process and the machine used.1 mark
    2. (ii)Name the three layers.1 mark
    3. (iii)Why does the red layer collect at the bottom? Name the dispersed phase and the dispersion medium in blood.2 marks
    4. OR
    5. (iii)Name a low-cost device that does the same job without electricity, and say why it is useful.2 marks
    Show answer

    (i) Centrifugation, in a centrifuge.

    (ii) Top: plasma; middle: white blood cells and platelets; bottom: red blood cells.

    (iii) Red blood cells are the heaviest part, so spinning throws them outwards, to the bottom of the tube. Dispersed phase: blood cells and platelets; dispersion medium: plasma.

    OR (iii): the paperfuge, a hand-spun cardboard disc on a string. It is cheap and needs no electricity, so it helps test blood for diseases such as malaria and anaemia in remote places.

  3. Q28
    Analytical thinkingRead the case and answer the questions.

    A town’s water-treatment plant takes in muddy river water. It first lets the water stand in large tanks, then adds alum, lets it stand again, and finally passes the water through beds of sand and gravel before adding chlorine.

    1. (i)Name the process taking place when the water stands in the first tanks.1 mark
    2. (ii)What is the job of alum? Name this process.1 mark
    3. (iii)Why are both settling and filtration needed? Why is the river water described as a suspension?2 marks
    4. OR
    5. (iii)Give two other uses of separation in society that help keep the environment clean.2 marks
    Show answer

    (i) Sedimentation: the heavier mud particles settle at the bottom.

    (ii) Alum is a coagulant: it makes the fine particles clump into larger lumps that settle. The process is coagulation.

    (iii) Settling removes most of the particles cheaply, but the finest ones stay suspended; filtration through sand removes what is left. The water is a suspension because its mud particles are large enough to see and settle when left undisturbed.

    OR (iii): treating sewage so that the clean water can be reused, and segregating waste at home into dry (recyclable) and wet (compostable) waste. Recovering metals such as lithium from old batteries is another.

5 marks each

Long answer questions

  1. Q29
    UnderstandingWhat is distillation? Draw a labelled diagram of the apparatus used to separate acetone from water. Why can the two be separated this way? How is fractional distillation different from it?
    Show answer

    Distillation is the process of heating a liquid mixture until the liquid with the lower boiling point turns to vapour, and then cooling the vapour so that it condenses back into a pure liquid (the distillate).

    A distillation set-up. A mixture of acetone and water is heated in a distillation flask on a tripod and wire gauze over a burner. A thermometer in the neck reads the temperature of the vapour. The vapour passes into a sloping water condenser, with cold water entering at the lower end and leaving at the upper end. The condensed liquid, acetone, drips into a conical flask.ThermometerWater outCondenserWater inDistillate(acetone)Conical flaskDistillationflaskAcetoneand waterWire gauzeBurner
    Separating acetone from water by distillation.

    Acetone (about 56 °C) and water (100 °C) are miscible, but their boiling points differ by 44 °C, which is more than about 25 °C. Acetone vaporises first, is condensed in the water condenser and collects in the conical flask; water stays in the distillation flask.

    Fractional distillation is used when boiling points differ by less than about 25 °C. A tall fractionating column, hot at the bottom and cooler at the top, lets each liquid condense at a different height, for example the fractions of crude oil: petroleum gas, petrol, kerosene, diesel, lubricating oil and bitumen.

  2. Q30
    Analytical thinkingCompare solutions, suspensions and colloids under five headings, giving two examples of each. How would you show in the laboratory which of three unlabelled beakers holds each kind?
    Show answer
    PropertySolutionSuspensionColloid
    NatureHomogeneousHeterogeneousHeterogeneous
    Particle sizeLess than 1 nmMore than 1000 nm1–1000 nm
    Visibility of particlesNot visibleVisible to the naked eyeNot visible to the naked eye
    SettlingDoes not settleSettlesDoes not settle
    FiltrationPasses throughResidue left on filterPasses through
    Tyndall effectNoYesYes
    ExamplesSalt water, vinegarMuddy water, chalk in waterMilk, blood
    1. Shine a narrow beam of light (a torch or laser) through each beaker from the side. The beam is not seen in the solution.
    2. Leave the other two to stand: the one in which particles settle (and which leaves a residue on filter paper) is the suspension.
    3. The remaining one, which scatters light but does not settle or filter out, is the colloid.
  3. Q31
    ApplicationSuggest a method to separate each of the following, and give the property used: (i) dyes in a black ink, (ii) kerosene from water, (iii) pure potassium nitrate from a sample containing a little common salt, (iv) iodine from sand, (v) pure water from seawater.
    Show answer
    MixtureMethodProperty used
    (i) Dyes in black inkPaper chromatographyThe dyes move up the paper with the solvent at different speeds
    (ii) Kerosene from waterSeparating funnelImmiscible liquids of different densities (kerosene floats)
    (iii) Potassium nitrate with a little saltCrystallisationPotassium nitrate’s solubility falls sharply on cooling; the small amount of salt stays dissolved
    (iv) Iodine from sandSublimationIodine sublimes on heating; sand does not
    (v) Pure water from seawaterDistillationWater boils and its vapour is condensed; the salts do not vaporise