Chapter 11 · Physics

Electricity

How electric charges move through a circuit, what controls the current, and how electrical energy turns into heat.

Step-by-step answers to all 41 questions in this chapter of the NCERT textbook: the in-text questions after each section, and the exercises at the end. Each question is given exactly as it appears in the book.

In-text questions

11.1 Electric current and circuit

  1. Q1
    What does an electric circuit mean?

    Answer

    An electric circuit is a continuous and closed path along which an electric current flows. It is made of a source, such as a cell or a battery, connecting wires, a switch and the devices that use the current, such as bulbs. If the path is broken anywhere, the current stops flowing.

  2. Q2
    Define the unit of current.

    Answer

    The SI unit of electric current is the ampere (A). One ampere is the current that flows when one coulomb of charge passes through a cross-section of a conductor in one second.

    1 A=1 C1 s
  3. Q3
    Calculate the number of electrons constituting one coulomb of charge.

    Answer

    The charge on one electron is e = 1.6 × 10−19 C. If n electrons together carry a charge of Q = 1 C, then Q = ne, so

    n=Qe=1 C1.6 × 10−19 C=6.25 × 1018

    So 6.25 × 1018 electrons make up one coulomb of charge.

In-text questions

11.2 Electric potential and potential difference

  1. Q1
    Name a device that helps to maintain a potential difference across a conductor.

    Answer

    A cell or a battery. The chemical reactions inside it keep a potential difference between its terminals, even while a current is flowing.

  2. Q2
    What is meant by saying that the potential difference between two points is 1 V?

    Answer

    It means that 1 joule of work is done to move a charge of 1 coulomb from one point to the other.

    1 V=1 J1 C
  3. Q3
    How much energy is given to each coulomb of charge passing through a 6 V battery?

    Answer

    The energy given to a charge equals the work done on it, which is the potential difference multiplied by the charge.

    W=VQ=6 V × 1 C=6 J

    Each coulomb of charge is given 6 J of energy.

In-text questions

11.5 Factors on which the resistance of a conductor depends

  1. Q1
    On what factors does the resistance of a conductor depend?

    Answer

    The resistance of a conductor depends on:

    1. its length: resistance is directly proportional to length, R ∝ l;
    2. its area of cross-section: resistance is inversely proportional to area, R ∝ 1A;
    3. the nature of its material, that is, the resistivity of the material;
    4. its temperature.

    The first three together give R = ρlA, where ρ is the resistivity of the material.

  2. Q2
    Will current flow more easily through a thick wire or a thin wire of the same material, when connected to the same source? Why?

    Answer

    Current flows more easily through the thick wire.

    Resistance is inversely proportional to the area of cross-section. A thick wire has a larger area of cross-section, so its resistance is lower. With the same source, a lower resistance allows a larger current to flow.

  3. Q3
    Let the resistance of an electrical component remains constant while the potential difference across the two ends of the component decreases to half of its former value. What change will occur in the current through it?

    Answer

    The current also becomes half of its former value.

    By Ohm’s law, I = VR. When the potential difference becomes V2 and R stays the same, the new current is

    I′=V2R=12 × VR=I2
  4. Q4
    Why are coils of electric toasters and electric irons made of an alloy rather than a pure metal?

    Answer

    1. The resistivity of an alloy is higher than that of the pure metals it is made from.
    2. An alloy does not oxidise (burn) readily, even at the high temperatures reached in a toaster or an iron.
  5. Q5
    Use the data in Table 11.2 to answer the following –(a) Which among iron and mercury is a better conductor?(b) Which material is the best conductor?

    Answer

    The lower the resistivity of a material, the better it conducts. In Table 11.2 of the textbook, iron has a resistivity of 10.0 × 10−8 Ω m and mercury has 94.0 × 10−8 Ω m. Silver has the lowest resistivity of all, 1.60 × 10−8 Ω m.

    (a) Iron is a better conductor than mercury, because its resistivity is lower.

    (b) Silver is the best conductor, because it has the lowest resistivity in the table.

In-text questions

11.6 Resistors in series

  1. Q1
    Draw a schematic diagram of a circuit consisting of a battery of three cells of 2 V each, a 5 Ω resistor, an 8 Ω resistor, and a 12 Ω resistor, and a plug key, all connected in series.

    Answer

    A battery of three 2 V cells, a plug key and resistors of 5 ohms, 8 ohms and 12 ohms, all joined in series. +− 3 cells of 2 V each Plug key 5 Ω8 Ω12 Ω
    A battery of three 2 V cells, a plug key and resistors of 5 Ω, 8 Ω and 12 Ω, all in series.

    The three cells are joined one after another, the positive terminal of one to the negative terminal of the next, to make a 6 V battery. All the parts are joined in a single loop, so there is only one path for the current.

  2. Q2
    Redraw the circuit of Question 1, putting in an ammeter to measure the current through the resistors and a voltmeter to measure the potential difference across the 12 Ω resistor. What would be the readings in the ammeter and the voltmeter?

    Answer

    A battery of three 2 V cells, a plug key, an ammeter and resistors of 5 ohms, 8 ohms and 12 ohms, all joined in series. A voltmeter is joined in parallel across the 12 ohm resistor. +− 3 cells of 2 V each Plug key 5 Ω8 Ω12 ΩAAmmeterVVoltmeter
    The ammeter is joined in series, and the voltmeter in parallel across the 12 Ω resistor.
    V=3 × 2 V=6 VRs=5 Ω + 8 Ω + 12 Ω=25 ΩI=VRs=6 V25 Ω=0.24 AV12=I × 12 Ω=0.24 A × 12 Ω=2.88 V

    The ammeter reads 0.24 A and the voltmeter reads 2.88 V.

In-text questions

11.6 Resistors in parallel

  1. Q1
    Judge the equivalent resistance when the following are connected in parallel – (a) 1 Ω and 106 Ω, (b) 1 Ω and 103 Ω, and 106 Ω.

    Answer

    In parallel, the equivalent resistance is always less than the smallest resistance. When one resistance is very much smaller than the others, the equivalent resistance is very close to it, but slightly less.

    (a)

    1Rp=11 Ω + 1106 Ω=106 + 1106 ΩRp=106106 + 1 Ω≈1 Ω

    The equivalent resistance is very nearly 1 Ω, just less than it (about 0.999999 Ω).

    (b)

    1Rp=11 Ω + 1103 Ω + 1106 Ω=106 + 103 + 1106 ΩRp=1061 001 001 Ω≈0.999 Ω

    The equivalent resistance is again very nearly 1 Ω, just less than it.

  2. Q2
    An electric lamp of 100 Ω, a toaster of resistance 50 Ω, and a water filter of resistance 500 Ω are connected in parallel to a 220 V source. What is the resistance of an electric iron connected to the same source that takes as much current as all three appliances, and what is the current through it?

    Answer

    1Rp=1100 Ω + 150 Ω + 1500 Ω=5 + 10 + 1500 Ω=16500 ΩRp=500 Ω16=31.25 Ω

    The iron takes as much current as all three appliances together, so its resistance must be equal to their equivalent resistance, 31.25 Ω.

    I=VR=220 V31.25 Ω=7.04 A

    The resistance of the iron is 31.25 Ω, and the current through it is 7.04 A.

  3. Q3
    What are the advantages of connecting electrical devices in parallel with the battery instead of connecting them in series?

    Answer

    1. Each device gets the full potential difference of the battery.
    2. Each device can be switched on or off without affecting the others.
    3. If one device stops working, the others keep working, because the circuit is not broken.
    4. Each device draws the current it needs, which depends on its own resistance. In series, every device would have to take the same current.
  4. Q4
    How can three resistors of resistances 2 Ω, 3 Ω, and 6 Ω be connected to give a total resistance of (a) 4 Ω, (b) 1 Ω?

    Answer

    (a) Join the 3 Ω and 6 Ω resistors in parallel, and join the 2 Ω resistor in series with this pair.

    A 2 ohm resistor in series with a 3 ohm and a 6 ohm resistor in parallel.2 Ω3 Ω6 Ω
    (a) 2 Ω in series with a parallel pair of 3 Ω and 6 Ω.
    1Rp=13 Ω + 16 Ω=2 + 16 Ω=36 Ω=12 ΩRp=2 ΩR=2 Ω + 2 Ω=4 Ω

    (b) Join all three resistors in parallel.

    Resistors of 2 ohms, 3 ohms and 6 ohms, all in parallel.2 Ω3 Ω6 Ω
    (b) 2 Ω, 3 Ω and 6 Ω, all in parallel.
    1R=12 Ω + 13 Ω + 16 Ω=3 + 2 + 16 Ω=66 Ω=11 ΩR=1 Ω
  5. Q5
    What is (a) the highest, (b) the lowest total resistance that can be secured by combinations of four coils of resistance 4 Ω, 8 Ω, 12 Ω, 24 Ω?

    Answer

    (a) The highest total resistance is obtained by joining all four coils in series.

    Rs=4 Ω + 8 Ω + 12 Ω + 24 Ω=48 Ω

    (b) The lowest total resistance is obtained by joining all four coils in parallel.

    1Rp=14 Ω + 18 Ω + 112 Ω + 124 Ω=6 + 3 + 2 + 124 Ω=1224 Ω=12 ΩRp=2 Ω

    The highest total resistance is 48 Ω and the lowest is 2 Ω.

In-text questions

11.7 Heating effect of electric current

  1. Q1
    Why does the cord of an electric heater not glow while the heating element does?

    Answer

    The cord and the heating element are joined in series, so the same current flows through both. The heat produced is H = I2Rt, so for the same current, more heat is produced where the resistance is higher.

    The cord is made of copper or aluminium, which has a very low resistance, so very little heat is produced in it. The heating element is made of an alloy with a much higher resistance, so it produces a lot of heat, becomes red hot and glows.

  2. Q2
    Compute the heat generated while transferring 96000 coulomb of charge in one hour through a potential difference of 50 V.

    Answer

    The heat generated equals the work done to move the charge through the potential difference. Since Q = It:

    H=VIt=VQ=50 V × 96 000 C=4 800 000 J=4.8 × 106 J

    The heat generated is 4.8 × 106 J. The time, one hour, is not needed, because the total charge is given.

  3. Q3
    An electric iron of resistance 20 Ω takes a current of 5 A. Calculate the heat developed in 30 s.

    Answer

    H=I2Rt=(5 A)2 × 20 Ω × 30 s=15 000 J=1.5 × 104 J

    The heat developed is 1.5 × 104 J.

In-text questions

11.8 Electric power

  1. Q1
    What determines the rate at which energy is delivered by a current?

    Answer

    The rate at which electrical energy is delivered is the electric power. It is determined by the potential difference V across the device and the current I through it: P = VI. For a resistor, this can also be written as P = I2R or P = V2R.

  2. Q2
    An electric motor takes 5 A from a 220 V line. Determine the power of the motor and the energy consumed in 2 h.

    Answer

    P=VI=220 V × 5 A=1100 WE=Pt=1100 W × 2 h=2200 W h=2.2 kWh=2.2 × 3.6 × 106 J=7.92 × 106 J

    The power of the motor is 1100 W, and the energy consumed in 2 h is 2.2 kWh, which is 7.92 × 106 J.

End of chapter

Exercises

  1. Q1
    A piece of wire of resistance R is cut into five equal parts. These parts are then connected in parallel. If the equivalent resistance of this combination is R′, then the ratio RR′ is –(a) 125(b) 15(c) 5(d) 25

    Answer

    (d) 25

    Each part has one-fifth of the length, so the resistance of each part is R5. Each part in parallel adds 5R to 1R′:

    1R′=5 × 5R=25RR′=R25RR′=25
  2. Q2
    Which of the following terms does not represent electrical power in a circuit?(a) I2R(b) IR2(c) VI(d) V2R

    Answer

    (b) IR2

    Electric power can be written as P = VI, P = I2R or P = V2R. The term IR2 is not one of these, so it does not represent power.

  3. Q3
    An electric bulb is rated 220 V and 100 W. When it is operated on 110 V, the power consumed will be –(a) 100 W(b) 75 W(c) 50 W(d) 25 W

    Answer

    (d) 25 W

    First find the resistance of the bulb from its rating:

    R=V2P=(220 V)2100 W=484 Ω

    On 110 V, the resistance stays the same, so the power consumed is

    P′=(110 V)2484 Ω=12 100484 W=25 W

    Halving the voltage makes the power one-fourth.

  4. Q4
    Two conducting wires of the same material and of equal lengths and equal diameters are first connected in series and then parallel in a circuit across the same potential difference. The ratio of heat produced in series and parallel combinations would be –(a) 1:2(b) 2:1(c) 1:4(d) 4:1

    Answer

    (c) 1:4

    Let the resistance of each wire be R. In series, the total resistance is 2R. In parallel, it is R2. Across the same potential difference V, for the same time t, the heat produced is H = V2tR (from H = I2Rt with I = VR). Dividing by R2 is the same as multiplying by 2R, so

    Hs=V2t2RHp=2V2tR=4 × V2t2R=4Hs

    So the heat produced in series and in parallel are in the ratio 1:4.

  5. Q5
    How is a voltmeter connected in the circuit to measure the potential difference between two points?

    Answer

    A voltmeter is connected in parallel across the two points between which the potential difference is to be measured. Its positive (+) terminal is joined to the point at the higher potential, which is the side nearer the positive terminal of the battery.

    A battery, a switch, an ammeter, a rheostat and a resistor R joined in series. A voltmeter is joined in parallel across the resistor R. +− Battery Switch A Ammeter Rheostat Resistor R V Voltmeter I
    The voltmeter V is joined in parallel across the resistor R.
  6. Q6
    A copper wire has diameter 0.5 mm and resistivity of 1.6 × 10−8 Ω m. What will be the length of this wire to make its resistance 10 Ω? How much does the resistance change if the diameter is doubled?

    Answer

    The diameter is 0.5 mm, so the radius is r = 0.25 mm = 2.5 × 10−4 m.

    A=πr2=3.14 × (2.5 × 10−4 m)2=1.9625 × 10−7 m2l=RAρ=10 Ω × 1.9625 × 10−7 m21.6 × 10−8 Ω m≈122.7 m

    If the diameter is doubled, the radius doubles and the area of cross-section becomes 4 times larger. Resistance is inversely proportional to the area, so the new resistance is

    R′=10 Ω4=2.5 Ω

    The wire must be about 122.7 m long. If the diameter is doubled, the resistance falls from 10 Ω to 2.5 Ω: it becomes one-fourth, a decrease of 7.5 Ω.

  7. Q7
    The values of current I flowing in a given resistor for the corresponding values of potential difference V across the resistor are given below –
    I (amperes)0.51.02.03.04.0
    V (volts)1.63.46.710.213.2
    I (amperes)V (volts)
    0.51.6
    1.03.4
    2.06.7
    3.010.2
    4.013.2
    Plot a graph between V and I and calculate the resistance of that resistor.

    Answer

    Plot V on the vertical axis against I on the horizontal axis, and mark the five points. They lie very nearly on a straight line through the origin, so draw the straight line through the origin that passes as close as possible to all of them.

    Graph of potential difference V against current I for the readings 0.5 A and 1.6 V, 1.0 A and 3.4 V, 2.0 A and 6.7 V, 3.0 A and 10.2 V, and 4.0 A and 13.2 V. The best straight line through the origin rises by 10.0 V for every 3.0 A, so the resistance is about 3.3 ohms. 1.02.03.04.024681012140 ΔI = 3.0 A ΔV = 10.0 V Current, I (in A) Potential difference, V (in V)
    V–I graph for the given readings, with the best straight line through the origin.

    The slope of this line is the resistance. Take two points on the line, for example at 1.0 A and at 4.0 A:

    R=ΔVΔI=13.3 V − 3.3 V4.0 A − 1.0 A=10.0 V3.0 A≈3.3 Ω

    The resistance of the resistor is about 3.3 Ω. Depending on how the line is drawn, any value from about 3.3 Ω to 3.4 Ω is acceptable.

  8. Q8
    When a 12 V battery is connected across an unknown resistor, there is a current of 2.5 mA in the circuit. Find the value of the resistance of the resistor.

    Answer

    The current is I = 2.5 mA = 2.5 × 10−3 A.

    R=VI=12 V2.5 × 10−3 A=4800 Ω=4.8 kΩ

    The resistance of the resistor is 4800 Ω (4.8 kΩ).

  9. Q9
    A battery of 9 V is connected in series with resistors of 0.2 Ω, 0.3 Ω, 0.4 Ω, 0.5 Ω and 12 Ω, respectively. How much current would flow through the 12 Ω resistor?

    Answer

    Rs=0.2 Ω + 0.3 Ω + 0.4 Ω + 0.5 Ω + 12 Ω=13.4 ΩI=VRs=9 V13.4 Ω≈0.67 A

    In a series circuit, the same current flows through every resistor, so about 0.67 A flows through the 12 Ω resistor.

  10. Q10
    How many 176 Ω resistors (in parallel) are required to carry 5 A on a 220 V line?

    Answer

    The total resistance needed to carry 5 A on a 220 V line is

    R=VI=220 V5 A=44 Ω

    When n resistors of 176 Ω each are joined in parallel, their equivalent resistance is 176 Ωn. So

    176 Ωn=44 Ωn=176 Ω44 Ω=4

    4 resistors are required.

  11. Q11
    Show how you would connect three resistors, each of resistance 6 Ω, so that the combination has a resistance of (i) 9 Ω, (ii) 4 Ω.

    Answer

    (i) Join two of the resistors in parallel, and join the third in series with this pair.

    A 6 ohm resistor in series with two 6 ohm resistors in parallel.6 Ω6 Ω6 Ω
    (i) One 6 Ω resistor in series with two 6 Ω resistors in parallel.
    1Rp=16 Ω + 16 Ω=26 Ω=13 ΩRp=3 ΩR=6 Ω + 3 Ω=9 Ω

    (ii) Join two of the resistors in series, and join the third in parallel with this pair.

    Two 6 ohm resistors in series, joined in parallel with a third 6 ohm resistor.6 Ω6 Ω6 Ω
    (ii) Two 6 Ω resistors in series, in parallel with the third.
    Rs=6 Ω + 6 Ω=12 Ω1R=112 Ω + 16 Ω=1 + 212 Ω=312 Ω=14 ΩR=4 Ω
  12. Q12
    Several electric bulbs designed to be used on a 220 V electric supply line, are rated 10 W. How many lamps can be connected in parallel with each other across the two wires of 220 V line if the maximum allowable current is 5 A?

    Answer

    The resistance of one bulb, from its rating, is

    R1=V2P=(220 V)210 W=4840 Ω

    The smallest total resistance allowed, so that the current is not more than 5 A, is

    R=VI=220 V5 A=44 Ω

    For n equal bulbs in parallel, R = R1n, so

    n=R1R=4840 Ω44 Ω=110

    110 lamps can be connected in parallel.

  13. Q13
    A hot plate of an electric oven connected to a 220 V line has two resistance coils A and B, each of 24 Ω resistance, which may be used separately, in series, or in parallel. What are the currents in the three cases?

    Answer

    (i) One coil used on its own:

    I=VR=220 V24 Ω≈9.17 A

    (ii) The two coils in series:

    Rs=24 Ω + 24 Ω=48 ΩI=VRs=220 V48 Ω≈4.58 A

    (iii) The two coils in parallel:

    1Rp=124 Ω + 124 Ω=224 Ω=112 ΩRp=12 ΩI=VRp=220 V12 Ω≈18.33 A

    The currents are about 9.17 A when a coil is used on its own, 4.58 A in series and 18.33 A in parallel.

  14. Q14
    Compare the power used in the 2 Ω resistor in each of the following circuits: (i) a 6 V battery in series with 1 Ω and 2 Ω resistors, and (ii) a 4 V battery in parallel with 12 Ω and 2 Ω resistors.

    Answer

    (i) The resistors are in series, so the same current flows through both.

    R=1 Ω + 2 Ω=3 ΩI=VR=6 V3 Ω=2 AP=I2R=(2 A)2 × 2 Ω=8 W

    (ii) The resistors are in parallel with the battery, so the 2 Ω resistor has the full 4 V across it.

    P=V2R=(4 V)22 Ω=8 W

    The power used in the 2 Ω resistor is the same, 8 W, in both circuits.

  15. Q15
    Two lamps, one rated 100 W at 220 V, and the other 60 W at 220 V, are connected in parallel to electric mains supply. What current is drawn from the line if the supply voltage is 220 V?

    Answer

    In parallel, each lamp gets the full 220 V, so each uses its rated power. The current drawn from the line is the sum of the two lamp currents.

    I1=100 W220 V≈0.455 AI2=60 W220 V≈0.273 AI=I1 + I2≈0.455 A + 0.273 A≈0.73 A

    The current drawn from the line is about 0.73 A.

  16. Q16
    Which uses more energy, a 250 W TV set in 1 hr, or a 1200 W toaster in 10 minutes?

    Answer

    ETV=250 W × 3600 s=900 000 J=9 × 105 JEtoaster=1200 W × 600 s=720 000 J=7.2 × 105 J

    The TV set uses more energy: 9 × 105 J, compared with 7.2 × 105 J for the toaster. In kilowatt hours, that is 0.25 kWh compared with 0.2 kWh.

  17. Q17
    An electric heater of resistance 44 Ω draws 5 A from the service mains for 2 hours. Calculate the rate at which heat is developed in the heater.

    Answer

    The rate at which heat is developed is the power of the heater.

    P=I2R=(5 A)2 × 44 Ω=1100 W

    Heat is developed at the rate of 1100 W, that is, 1100 J every second. The time, 2 hours, is not needed for the rate. In that time, the total heat produced is 1100 W × 7200 s = 7.92 × 106 J.

  18. Q18
    Explain the following.(a) Why is the tungsten used almost exclusively for filament of electric lamps?(b) Why are the conductors of electric heating devices, such as bread-toasters and electric irons, made of an alloy rather than a pure metal?(c) Why is the series arrangement not used for domestic circuits?(d) How does the resistance of a wire vary with its area of cross-section?(e) Why are copper and aluminium wires usually employed for electricity transmission?

    Answer

    (a) Tungsten has a very high melting point (3380 °C). A filament must become white hot to give out light, and tungsten can reach this temperature without melting. Inside the bulb, which is filled with unreactive gases such as nitrogen and argon, the hot filament does not burn away easily.

    (b) The resistivity of an alloy is higher than that of the pure metals it is made from, and an alloy does not oxidise (burn) readily at high temperatures.

    (c) In a series arrangement, the supply voltage is shared between the appliances, so none of them gets the 220 V it is made for, and every appliance has to take the same current. If one appliance fails or is switched off, the circuit is broken and all the others stop working too.

    (d) For wires of the same material and length, the resistance is inversely proportional to the area of cross-section, R ∝ 1A. A thicker wire has less resistance: doubling the area of cross-section halves the resistance.

    (e) Copper and aluminium have very low resistivities, so they are very good conductors, and very little energy is wasted as heat in the transmission wires. Aluminium is also light and cheaper than copper.

Revising for the board exam?Get the Chapter 11 revision PDF: quick notes, 20 new board-pattern questions and full answers, for ₹49.