Chapter 11 · Physics

Electricity

How electric charges move through a circuit, what controls the current, and how electrical energy turns into heat.

Questions on the patterns that come up most often in school tests and the board exam, in the same formats as the board paper. Each question shows the skill it tests. Try each one before you open the answer.

What the board asks most

How this chapter is tested

  • Physics carries 25 of the 80 marks in the Science paper, in 10 questions.
  • Electricity and Magnetic effects together carry 13 marks. Electricity alone usually gets about 6 to 10 of them.
  • About half the marks are for competency-based questions: case-based, assertion–reason, and questions that apply ideas to new situations or data.

Asked most often, with questions to practise

  1. Numericals from appliance and bulb ratingsQ1Q6Q8Q19Q25
  2. Circuits with resistors in series and parallel, and meter readingsQ21Q22Q31Q33
  3. Joining resistors to get a given resistanceQ3Q18Q34
  4. Resistance and resistivity: stretched, cut or thicker wiresQ4Q14Q23Q35
  5. The fuse: how it works and choosing its ratingQ8Q20Q26
  6. Joule’s law of heatingQ17Q27Q36
  7. Series or parallel: current, voltage and brightnessQ6Q13Q30
  8. Ohm’s law experiment and the V–I graphQ2Q24Q32

1 mark each

Multiple choice questions

  1. Q1
    ApplicationAn electric iron is rated 1100 W, 220 V. What current does it draw when it works at its rated voltage?(a) 0.2 A(b) 2 A(c) 5 A(d) 20 A
    Show answer

    (c) 5 A

    I=PV=1100 W220 V=5 A
  2. Q2
    Analytical thinkingThe graph shows how the potential difference V across two wires, P and Q, changes with the current I through them. The wires are made of the same material and have the same length. Which wire is thinner?(a) P, because its line is steeper, so it has more resistance(b) Q, because its line is less steep, so it has more resistance(c) P, because its line is steeper, so it has less resistance(d) Neither: they are equally thick, because both lines are straight
    Graph of potential difference V against current I for two wires, P and Q. Both are straight lines through the origin; the line for P is steeper than the line for Q.PQCurrent, IPotential difference, V
    The V–I graphs of wires P and Q.
    Show answer

    (a) P, because its line is steeper, so it has more resistance

    On a graph of V against I, the slope VI is the resistance. The line for P is steeper, so P has the larger resistance. For wires of the same material and length, R = ρlA, so the wire with the larger resistance has the smaller area of cross-section. P is thinner.

  3. Q3
    ApplicationA wire of resistance 12 Ω is cut into three equal pieces, and the pieces are joined in parallel. The resistance of the combination is(a) 36 Ω(b) 12 Ω(c) 4 Ω(d) 43 Ω
    Show answer

    (d) 43 Ω

    Each piece has one-third of the length, so a resistance of 4 Ω. For n equal resistors, each of resistance r, in parallel, the equivalent resistance is rn:

    Rp=4 Ω3≈1.33 Ω
  4. Q4
    Critical thinkingA copper wire is stretched to twice its length. What happens to its resistivity?(a) It doubles(b) It becomes four times as much(c) It becomes half(d) It stays the same
    Show answer

    (d) It stays the same

    Resistivity depends only on the material and its temperature, and stretching changes neither. The resistance becomes four times as much (twice the length and half the area), but the resistivity does not change.

  5. Q5
    ApplicationA current of 0.5 A flows through a bulb for 10 minutes. How much charge flows through it?(a) 5 C(b) 30 C(c) 300 C(d) 3000 C
    Show answer

    (c) 300 C

    The time must be in seconds: 10 min = 600 s.

    Q=It=0.5 A × 600 s=300 C
  6. Q6
    Critical thinkingTwo bulbs rated 40 W, 220 V and 100 W, 220 V are joined in series across the 220 V mains. Which statement is correct?(a) The 100 W bulb glows more brightly(b) The 40 W bulb glows more brightly(c) Both bulbs glow equally brightly(d) Neither bulb glows
    Show answer

    (b) The 40 W bulb glows more brightly

    The resistance of each bulb is R = V2P:

    R40 W=(220 V)240 W=1210 ΩR100 W=(220 V)2100 W=484 Ω

    In series, the same current flows through both bulbs, so the power P = I2R is larger in the bulb with the larger resistance. The 40 W bulb uses more power and glows more brightly.

  7. Q7
    UnderstandingThe resistance of an ideal ammeter and of an ideal voltmeter should be(a) zero and zero(b) zero and infinitely large(c) infinitely large and zero(d) infinitely large and infinitely large
    Show answer

    (b) zero and infinitely large

    An ammeter is joined in series, so it must not add any resistance to the circuit. A voltmeter is joined in parallel, so it must not draw any current away from the component.

  8. Q8
    ApplicationA geyser rated 1500 W, 220 V is fitted in a house. Which fuse should be used with it?(a) 2 A(b) 5 A(c) 10 A(d) 30 A
    Show answer

    (c) 10 A

    I=PV=1500 W220 V≈6.8 A

    The fuse must carry the normal current of 6.8 A without melting, but melt if the current rises well above it. A 2 A or 5 A fuse would melt in normal use, and a 30 A fuse would let a dangerously large current flow.

1 mark each

Assertion–reason questions

Each question has two statements: an Assertion (A) and a Reason (R). Choose the correct option:

  1. (a)Both A and R are true, and R is the correct explanation of A.
  2. (b)Both A and R are true, but R is not the correct explanation of A.
  3. (c)A is true, but R is false.
  4. (d)A is false, but R is true.
  1. Q9
    UnderstandingAssertion (A): About 6.25 × 1018 electrons together carry a charge of 1 C.Reason (R): The charge on one electron is 1.6 × 10−19 C.
    Show answer

    (a) Both A and R are true, and R is the correct explanation of A.

    The number of electrons in 1 C is the total charge divided by the charge on one electron:

    n=1 C1.6 × 10−19 C=6.25 × 1018
  2. Q10
    UnderstandingAssertion (A): The heating element of an electric iron is made of nichrome.Reason (R): Nichrome has a high resistivity and does not burn easily even when it is red hot.
    Show answer

    (a) Both A and R are true, and R is the correct explanation of A.

    Its high resistivity gives the element a high resistance. The element and the copper cord carry the same current, so by H = I2Rt the element gets hot while the cord stays cool. As an alloy, nichrome also does not oxidise (burn) at high temperatures. That is why it is used.

  3. Q11
    Critical thinkingAssertion (A): Copper is used to make connecting wires.Reason (R): Copper is a good conductor of heat.
    Show answer

    (b) Both A and R are true, but R is not the correct explanation of A.

    Both statements are true, but copper is used for wires because it has a very low electrical resistivity, so little energy is wasted as heat in the wires.

  4. Q12
    Critical thinkingAssertion (A): A 100 W, 220 V bulb has less resistance than a 60 W, 220 V bulb.Reason (R): When each is lit on its own from the 220 V mains, the 100 W bulb gives more light.
    Show answer

    (b) Both A and R are true, but R is not the correct explanation of A.

    Both statements are true, but the brighter light is a result of the lower resistance, not its cause. The assertion is true because resistance = V2P: for the same voltage, a bulb of higher power has less resistance.

  5. Q13
    UnderstandingAssertion (A): Household appliances are joined in parallel.Reason (R): The equivalent resistance of resistors in parallel is more than the largest of them.
    Show answer

    (c) A is true, but R is false.

    The equivalent resistance of resistors in parallel is less than the smallest of them. Appliances are joined in parallel so that each gets the full supply voltage and can be switched on or off on its own.

  6. Q14
    UnderstandingAssertion (A): A wire of the same material and thickness but twice the length has twice the resistance.Reason (R): The resistance of a wire is inversely proportional to its length.
    Show answer

    (c) A is true, but R is false.

    Resistance is directly proportional to length, so doubling the length doubles the resistance.

  7. Q15
    UnderstandingAssertion (A): An ammeter is joined in parallel with the component whose current is to be measured.Reason (R): An ammeter has a very low resistance.
    Show answer

    (d) A is false, but R is true.

    An ammeter is joined in series, so that the whole current passes through it. Its resistance is kept very low so that it does not change the current it measures.

2 marks each

Very short answer questions

  1. Q16
    UnderstandingDefine 1 volt. How much work is done in moving a charge of 2 C between two points that have a potential difference of 12 V?
    Show answer

    The potential difference between two points is 1 volt when 1 joule of work is done to move a charge of 1 coulomb from one point to the other: 1 V = 1 J1 C.

    W=VQ=12 V × 2 C=24 J
  2. Q17
    UnderstandingState Joule’s law of heating. If the current through a heater coil is doubled, how does the heat produced in a given time change?
    Show answer

    Joule’s law: the heat produced in a resistor is directly proportional to the square of the current, to the resistance and to the time for which the current flows: H = I2Rt.

    Hnew=(2I)2Rt=4I2Rt=4H

    The heat produced becomes four times as much.

  3. Q18
    ApplicationHow would you join three resistors of 4 Ω, 6 Ω and 12 Ω to get an equivalent resistance of (a) 2 Ω (b) 9 Ω?
    Show answer

    (a) Join all three in parallel:

    1Rp=14 Ω + 16 Ω + 112 Ω=312 Ω + 212 Ω + 112 Ω=612 Ω=12 ΩRp=2 Ω
    Resistors of 4, 6 and 12 ohms, all in parallel.4 Ω6 Ω12 Ω
    All three in parallel: 2 Ω.

    (b) Join the 4 Ω and 12 Ω resistors in parallel, and the 6 Ω resistor in series with them:

    1Rp=14 Ω + 112 Ω=412 Ω=13 ΩRp=3 ΩR=3 Ω + 6 Ω=9 Ω
    A 6 ohm resistor in series with 4 ohm and 12 ohm resistors in parallel.6 Ω4 Ω12 Ω
    6 Ω in series with 4 Ω and 12 Ω in parallel: 9 Ω.
  4. Q19
    Analytical thinkingTwo lamps are rated 60 W, 220 V and 100 W, 220 V. Which lamp has the greater resistance? Find the ratio of their resistances.
    Show answer

    For a lamp working at its rated voltage, R = V2P. Both lamps have the same voltage, so resistance is inversely proportional to power:

    R60 WR100 W=100 W60 W=53

    The 60 W lamp has the greater resistance, and the ratio of the resistances is 5 : 3.

  5. Q20
    Critical thinkingA 5 A fuse in a house circuit keeps blowing. A student replaces it with a 15 A fuse so that it “will not blow again”. Explain why this is dangerous.
    Show answer

    A fuse is chosen so that it melts as soon as the current rises above the safe limit for the wiring and the appliances on that circuit. A 15 A fuse would let up to 15 A flow before melting. Such a large current can overheat the wires and the appliances and start a fire. The right step is to find out why the fuse keeps blowing (an overload or a short circuit) and put that right.

  6. Q21
    Analytical thinkingA 6 Ω resistor is joined to a 12 V battery. A second 6 Ω resistor is then joined in parallel with the first. How does the current drawn from the battery change? Show by calculation.
    Show answer

    With one resistor:

    I=12 V6 Ω=2 A

    With two 6 Ω resistors in parallel, the equivalent resistance is 6 Ω2 = 3 Ω:

    I′=12 V3 Ω=4 A

    The current drawn from the battery doubles, from 2 A to 4 A.

3 marks each

Short answer questions

  1. Q22
    Analytical thinkingIn the circuit shown, find(a) the total resistance of the circuit(b) the reading of the ammeter(c) the potential difference across the 6 Ω resistor, and the current through it.
    A 12 volt battery, a key and an ammeter joined to a 4 ohm resistor, which is in series with a 6 ohm and a 12 ohm resistor joined in parallel.12 VA4 Ω6 Ω12 Ω
    A 4 Ω resistor in series with 6 Ω and 12 Ω resistors in parallel.
    Show answer

    (a) The 6 Ω and 12 Ω resistors are in parallel:

    1Rp=16 Ω + 112 Ω=312 Ω=14 ΩRp=4 Ω

    This pair is in series with the 4 Ω resistor:

    R=Rp + 4 Ω=4 Ω + 4 Ω=8 Ω

    (b)

    I=VR=12 V8 Ω=1.5 A

    (c) The whole current, 1.5 A, flows through the parallel pair, so the potential difference across it is

    Vp=IRp=1.5 A × 4 Ω=6 VI6 Ω=6 V6 Ω=1 A

    The potential difference across the 6 Ω resistor is 6 V, and the current through it is 1 A.

  2. Q23
    Analytical thinkingA wire is 50 m long, has an area of cross-section of 0.5 mm2, and has a resistance of 1.7 Ω. Find the resistivity of its material. Then use the table to name the metal.
    MetalResistivity (in Ω m)
    Silver1.6 × 10−8
    Copper1.7 × 10−8
    Aluminium2.7 × 10−8
    Tungsten5.6 × 10−8
    Show answer
    A=0.5 mm2=0.5 × 10−6 m2ρ=RAl=1.7 Ω × 0.5 × 10−6 m250 m=1.7 × 10−8 Ω m

    This matches the resistivity of copper.

  3. Q24
    Critical thinkingTo verify Ohm’s law, a student records these readings for a resistor:
    V (volts)1.02.03.04.05.0
    I (amperes)0.200.400.750.801.00
    V (volts)I (amperes)
    1.00.20
    2.00.40
    3.00.75
    4.00.80
    5.01.00
    (a) Find the resistance of the resistor.(b) Which reading is most likely a mistake? Give a reason.(c) What shape will the V–I graph have?
    Show answer

    (a) For four of the readings, VI comes out the same, for example:

    R=2.0 V0.40 A=5 Ω

    The resistance is 5 Ω.

    (b) The third reading. For it, 3.0 V0.75 A = 4 Ω, unlike all the others. With a 5 Ω resistor, the current at 3.0 V should be 3.0 V5 Ω = 0.60 A.

    (c) A straight line through the origin, with a slope of 5 Ω (leaving out the wrong reading).

  4. Q25
    ApplicationAn electric heater is rated 1100 W, 220 V. Find(a) its resistance(b) the current it draws at 220 V(c) the power it uses if it is run on 110 V. Take its resistance to stay the same.
    Show answer

    (a)

    R=V2P=(220 V)21100 W=44 Ω

    (b)

    I=PV=1100 W220 V=5 A

    (c)

    P′=V′2R=(110 V)244 Ω=275 W

    Halving the voltage cuts the power to a quarter, because power depends on the square of the voltage.

  5. Q26
    Analytical thinkingA house circuit at 220 V is protected by a 5 A fuse.(a) Find the current drawn by an 880 W heater.(b) An iron rated 440 W is switched on while the heater is running. What happens, and why?(c) Why is it useful that this happens?
    Show answer

    (a)

    I=PV=880 W220 V=4 A

    (b) The iron draws 440 W220 V = 2 A. Appliances in a house are joined in parallel, so their currents add: the total current becomes 4 A + 2 A = 6 A. This is more than 5 A, so the fuse wire heats up and melts, and the circuit is broken.

    (c) It stops a current larger than the safe limit from flowing, so the wiring and the appliances do not overheat or catch fire.

  6. Q27
    Analytical thinkingThree identical resistors are joined first in series and then in parallel, each time to the same battery. Find the ratio of the heat produced in the two cases in the same time.
    Show answer

    Let each resistor have resistance R and the battery voltage be V. In series, Rs = 3R. In parallel, Rp = R3. In time t, the heat produced is H = V2tR, using the total resistance:

    Hs=V2t3RHp=3V2tR

    So Hp is 9 times Hs, and the ratio of the heat in series to the heat in parallel is 1 : 9.

4 marks each

Case-based questions

  1. Q28
    ApplicationRead the case and answer the questions.

    Ritu’s family wants to understand their electricity bill. The table shows the main appliances in their home, the power of each, and how long each is used every day. Their electricity company charges ₹8 for each unit (kWh) of energy.

    AppliancePowerTime used each day
    Geyser2 kW1 h
    5 LED bulbs20 W each6 h
    Refrigerator100 W24 h
    Iron1 kW30 min
    1. (i)What is the commercial unit of electrical energy? How many joules is it equal to?1 mark
    2. (ii)How much energy does the geyser use each day?1 mark
    3. (iii)Find the total energy the family uses each day, and the cost of electricity for 30 days.2 marks
    4. OR
    5. (iii)What current does the geyser draw from the 220 V supply? Should it be on a 5 A circuit or a 15 A circuit?2 marks
    Show answer

    (i) The kilowatt hour (kWh). 1 kWh = 3.6 × 106 J.

    (ii)

    E=Pt=2 kW × 1 h=2 kWh

    (iii) The energy used each day by the other appliances:

    Ebulbs=5 × 0.02 kW × 6 h=0.6 kWhErefrigerator=0.1 kW × 24 h=2.4 kWhEiron=1 kW × 0.5 h=0.5 kWh

    The total energy each day, and then for 30 days:

    Eday=2 kWh + 0.6 kWh + 2.4 kWh + 0.5 kWh=5.5 kWh
    E30 days=5.5 kWh × 30=165 kWhCost=165 × ₹8=₹1320

    OR

    I=PV=2000 W220 V≈9.1 A

    This is more than 5 A, so the geyser must be on a 15 A circuit. On a 5 A circuit, the fuse would melt.

  2. Q29
    Analytical thinkingRead the case and answer the questions.

    Aman wants to find out what the resistance of a wire depends on. He joins a 2 V cell, a key and an ammeter in a circuit with two terminals, X and Y. He joins four wires between X and Y, one at a time, and notes the current each time.

    A 2 volt cell, a key and an ammeter joined in a loop with two terminals, X and Y. The wire under test is joined between X and Y.2 VAYXWire under test
    The wires are joined between X and Y, one at a time.
    WireMaterialLengthArea of cross-sectionCurrent
    1Nichrome50 cma0.4 A
    2Nichrome100 cma0.2 A
    3Nichrome50 cm2a0.8 A
    4Copper50 cmaAbove 3 A (off the scale)
    WireMaterial, length, areaCurrent
    1Nichrome, 50 cm, a0.4 A
    2Nichrome, 100 cm, a0.2 A
    3Nichrome, 50 cm, 2a0.8 A
    4Copper, 50 cm, aAbove 3 A
    1. (i)Which two wires show how resistance depends on length?1 mark
    2. (ii)What do the readings for wires 1 and 3 show about the area of cross-section?1 mark
    3. (iii)Find the resistance of wires 1 and 2. Take the resistance of the rest of the circuit to be negligible. What do the two values show?2 marks
    4. OR
    5. (iii)Why does wire 4 give such a large current? Which material, nichrome or copper, is better for the element of a heater? Give two reasons.2 marks
    Show answer

    (i) Wires 1 and 2: they have the same material and area, but different lengths.

    (ii) Wire 3 has twice the area of wire 1 and lets twice the current through, so it has half the resistance. Resistance is inversely proportional to the area of cross-section.

    (iii)

    R1=2 V0.4 A=5 ΩR2=2 V0.2 A=10 Ω

    Wire 2 is twice as long as wire 1 and has twice the resistance, so resistance is directly proportional to length.

    OR

    Copper has a far lower resistivity than nichrome, so a copper wire of the same size has a much smaller resistance and lets a much larger current through. Nichrome is better for a heater element, because (1) its high resistivity gives the coil a much larger resistance than the copper wires that carry the same current to it, so by H = I2Rt the heat is produced in the coil and not in the wires, and (2) as an alloy it does not burn (oxidise) easily at high temperatures.

  3. Q30
    Critical thinkingRead the case and answer the questions.

    For a festival, Kabir buys a string of 20 identical small bulbs joined in series. He plugs the string into the 220 V mains. Each bulb has a resistance of 22 Ω when it glows.

    1. (i)What is the potential difference across each bulb?1 mark
    2. (ii)One bulb fuses. What happens to the other bulbs, and why?1 mark
    3. (iii)Find the current in the string and the total power it uses.2 marks
    4. OR
    5. (iii)Kabir’s friend suggests joining the same 20 bulbs in parallel across the mains, so that one fused bulb will not put out the rest. Explain what would happen.2 marks
    Show answer

    (i) The 220 V is shared equally between the 20 identical bulbs: 220 V20 = 11 V across each bulb.

    (ii) All the other bulbs go off. In a series circuit there is only one path for the current, and the fused bulb breaks it.

    (iii)

    Rs=20 × 22 Ω=440 ΩI=220 V440 Ω=0.5 AP=VI=220 V × 0.5 A=110 W

    OR

    The friend is right that in parallel one fused bulb would not put out the rest, but these bulbs are made for 11 V. In parallel, each bulb would get the full 220 V, which is 20 times its working voltage. The current through each bulb would be 220 V22 Ω = 10 A, instead of the normal 11 V22 Ω = 0.5 A, which is 20 times as much. Since P = V2R, each bulb would use 400 times its normal power, and every bulb would overheat and fuse almost at once. Together the bulbs would also draw 20 × 10 A = 200 A, so the house fuse would blow.

  4. Q31
    Analytical thinkingRead the case and answer the questions.

    Meena has a 6 V battery, a key, an ammeter and two resistors of 4 Ω and 12 Ω. She joins the resistors first in series, as in arrangement (i), and then in parallel, as in arrangement (ii).

    Arrangement (i): a 6 volt battery, a key and an ammeter with a 4 ohm and a 12 ohm resistor in series.6 VA4 Ω12 Ω(i)
    Arrangement (ii): a 6 volt battery, a key and an ammeter with a 4 ohm and a 12 ohm resistor in parallel.6 VA4 Ω12 Ω(ii)
    The two arrangements.
    1. (i)In which arrangement does the battery supply the larger current?1 mark
    2. (ii)In arrangement (ii), what would a voltmeter read if it were joined across the 12 Ω resistor?1 mark
    3. (iii)Find the reading of the ammeter in each arrangement.2 marks
    4. OR
    5. (iii)Find the current through the 12 Ω resistor in each arrangement.2 marks
    Show answer

    (i) Arrangement (ii), in parallel, because its total resistance is less than either resistor alone.

    (ii) 6 V. Each resistor in parallel has the full battery voltage across it.

    (iii) In series:

    Rs=4 Ω + 12 Ω=16 ΩI=6 V16 Ω=0.375 A

    In parallel:

    1Rp=14 Ω + 112 Ω=412 Ω=13 ΩRp=3 ΩI=6 V3 Ω=2 A

    OR

    In series, the same current flows through both resistors:

    Rs=4 Ω + 12 Ω=16 ΩI12 Ω=6 V16 Ω=0.375 A

    In parallel, the 12 Ω resistor has the full 6 V across it:

    I12 Ω=6 V12 Ω=0.5 A

5 marks each

Long answer questions

  1. Q32
    Understanding(a) State Ohm’s law.(b) Draw a labelled circuit diagram to verify it, and describe how you would take the readings.(c) Draw the V–I graph you would expect, and explain how to find the resistance from it.
    Show answer

    (a) Ohm’s law: the current through a metallic conductor is directly proportional to the potential difference across its ends, provided its temperature stays the same. That is, V ∝ I, or V = IR.

    (b)

    A battery, a key, an ammeter, a rheostat and a resistor R joined in series. A voltmeter is joined in parallel across the resistor R. +− Battery Key A Ammeter Rheostat Resistor R V Voltmeter I
    A circuit to verify Ohm’s law.
    1. Join a battery, a key, an ammeter, a rheostat and a resistor (for example, a nichrome wire) in series. Join a voltmeter in parallel across the resistor.
    2. Close the key, and note the current I and the potential difference V.
    3. Change the current with the rheostat, and note four or five more pairs of readings.
    4. For each pair, work out VI. It comes out the same every time, so V ∝ I. This verifies Ohm’s law.

    (c)

    Graph of potential difference V against current I for a 10 ohm resistor. The points 0.1 A and 1 V, 0.2 A and 2 V, 0.3 A and 3 V, and 0.4 A and 4 V lie on a straight line through the origin. The slope, 2 V for every 0.2 A, equals the resistance, 10 ohms. 0.10.20.30.40.5123450 ΔI = 0.2 A ΔV = 2 V R = ΔVΔI = 10 Ω Current, I (in A) Potential difference, V (in V)
    The V–I graph of a resistor is a straight line through the origin.

    The graph is a straight line through the origin. The resistance is its slope: take two points on the line, and divide the change in V by the change in I.

  2. Q33
    Analytical thinkingIn the circuit shown, find(a) the equivalent resistance of the 3 Ω and 6 Ω resistors(b) the total resistance of the circuit(c) the reading of the ammeter(d) the reading of the voltmeter(e) the current through the 6 Ω resistor and the power used by the 2 Ω resistor.
    A 12 volt battery, a key and an ammeter joined to a 2 ohm resistor, which is in series with a 3 ohm and a 6 ohm resistor joined in parallel. A voltmeter is joined across the parallel pair.12 VA2 Ω3 Ω6 ΩV
    A 2 Ω resistor in series with 3 Ω and 6 Ω resistors in parallel, with a voltmeter across the parallel pair.
    Show answer

    (a)

    1Rp=13 Ω + 16 Ω=36 Ω=12 ΩRp=2 Ω

    (b) This pair is in series with the 2 Ω resistor:

    R=Rp + 2 Ω=2 Ω + 2 Ω=4 Ω

    (c)

    I=12 V4 Ω=3 A

    (d) The voltmeter reads the potential difference across the parallel pair:

    Vp=IRp=3 A × 2 Ω=6 V

    (e)

    I6 Ω=6 V6 Ω=1 AP2 Ω=I2R=(3 A)2 × 2 Ω=18 W
  3. Q34
    Application(a) Three resistors R1, R2 and R3 are joined in parallel to a battery. Derive the expression for their equivalent resistance.(b) Resistors of 10 Ω, 20 Ω and 20 Ω are joined in parallel to a 10 V battery. Find the equivalent resistance and the current drawn from the battery.
    A battery of voltage V, a key and an ammeter joined to three resistors, R1, R2 and R3, in parallel. The main current I divides into the branch currents I1, I2 and I3.VAIR1I1R2I2R3I3
    Three resistors in parallel.
    Show answer

    (a) Draw the circuit, marking the main current I and the branch currents I1, I2 and I3, as in the figure. In parallel, each resistor has the same potential difference V across it, and the main current I divides between them:

    I=I1 + I2 + I3

    By Ohm’s law, I1 = VR1, I2 = VR2 and I3 = VR3. For the equivalent resistance Rp, I = VRp. So

    VRp=VR1 + VR2 + VR3

    Dividing both sides by V:

    1Rp=1R1 + 1R2 + 1R3

    (b)

    1Rp=110 Ω + 120 Ω + 120 Ω=220 Ω + 120 Ω + 120 Ω=420 Ω=15 ΩRp=5 ΩI=10 V5 Ω=2 A
  4. Q35
    Understanding(a) Name the factors on which the resistance of a conductor depends, and write the relation between them.(b) Define resistivity, and give its SI unit.(c) Why are the elements of heating devices made of alloys, while the filaments of electric bulbs are made of tungsten?(d) A wire has a resistance of 10 Ω. What will its resistance be if it is stretched to three times its length?
    Show answer

    (a) The resistance of a conductor depends on its length l (directly proportional), its area of cross-section A (inversely proportional), the material it is made of, and its temperature: R = ρlA, where ρ is the resistivity of the material.

    (b) The resistivity of a material is the resistance of a conductor of that material that has unit length and unit area of cross-section. Its SI unit is the ohm metre (Ω m).

    (c) An alloy has a high resistivity, so the heating element has a much larger resistance than the copper wires that carry the same current to it. By H = I2Rt, the heat is produced in the element and not in the wires. Alloys also do not burn (oxidise) easily at high temperatures. Tungsten has a very high melting point (about 3380 °C), so a tungsten filament can glow white-hot without melting.

    (d) Its volume stays the same, so three times the length means one-third of the area. Each change on its own makes the resistance three times as much, so together they make it 3 × 3 = 9 times as much:

    R′=3 × 3 × 10 Ω=90 Ω
  5. Q36
    Application(a) Derive the expression H = I2Rt for the heat produced in a resistor.(b) Give two uses of the heating effect of electric current in daily life.(c) An electric iron of 1100 W is used for 30 minutes every day. Find the energy it uses in 30 days, and the cost at ₹7 per unit.
    Show answer

    (a) When a charge Q moves through a potential difference V, the work done is W = VQ. If a current I flows for a time t, then Q = It. In a resistor, all of this energy becomes heat:

    H=VIt=(IR)It=I2Rt

    using Ohm’s law, V = IR.

    (b) Any two of: electric iron, electric heater, toaster, kettle, electric bulb, and the electric fuse.

    (c) 1100 W = 1.1 kW and 30 min = 0.5 h, so in 30 days:

    E=Pt=1.1 kW × 0.5 h × 30=16.5 kWhCost=16.5 × ₹7=₹115.50
Revising for the board exam?Get the Chapter 11 revision PDF: quick notes, 20 new board-pattern questions and full answers, for ₹49.