Chapter 12 · Physics

Magnetic Effects of Electric Current

How an electric current makes a magnetic field, the field lines of a bar magnet, a straight wire, a loop and a solenoid, the right-hand thumb rule, electromagnets, the force on a current in a magnetic field and Fleming’s left-hand rule, and how the electric circuits in our homes are wired and kept safe.

Done reading? Try the Magnetism lab activity on this chapter.
In this chapter 14 topics
  1. 1Magnetic effect of electric current
  2. 2Magnets, magnetic field and field lines
  3. 3Properties of magnetic field lines
  4. 4Field due to a current in a straight conductor
  5. 5Right-hand thumb rule
  6. 6Field due to a current in a circular loop
  7. 7Field due to a current in a solenoid
  8. 8Electromagnets
  9. 9Force on a current-carrying conductor in a magnetic field
  10. 10Fleming’s left-hand rule
  11. 11Magnetism in medicine
  12. 12Domestic electric circuits
  13. 13The earth wire and earthing
  14. 14Short circuit, overloading and the fuse

1Magnetic effect of electric current

Magnetic effect of electric current

An electric current flowing through a conductor produces a magnetic field around it. So a current-carrying wire behaves like a magnet.

Oersted’s discovery

  • In 1820, Hans Christian Oersted noticed by chance that a compass needle turned when a current flowed in a wire nearby.
  • This showed that electricity and magnetism are linked. The study of this link is called electromagnetism.
  • His work later led to technologies such as radio, television and fibre optics.
  • A unit of magnetic field strength, the oersted, is named after him.

Activity: a compass near a current-carrying wire

  1. Join a thick copper wire XY in a circuit with a cell and a plug key.
  2. Place a small compass near the wire. Note where its needle points.
  3. Insert the key so that a current flows. The needle is deflected (it turns).
  4. Reverse the current. The needle now turns the opposite way.
A straight wire is held over a compass needle, along the north-south line. With no current the needle points north. When the current flows from north to south, the north pole of the needle turns towards the east; when the current is reversed, it turns towards the west.(a) No currentneedle pointsnorth(b) Currentnorth to south,N turns east(c) Currentsouth to north,N turns westNEWWire over the needle
Figure 1. A wire held over a compass needle, along the north-south line. The deflection reverses when the current reverses.
Current in the wire (wire over the needle)North pole of the needle turns
No currentStays pointing north
From north to southTowards the east
From south to northTowards the west
  • The needle turns only while the current flows. So the current makes the magnetic field.
  • Reversing the current reverses the direction of the magnetic field.

Remember

  • A current in a wire produces a magnetic field round it (Oersted, 1820).
  • Reverse the current and the magnetic field reverses too.
Quick checkA compass needle placed under a wire turns when the key is closed. What does this show?Show answer

The current in the wire produces a magnetic field around it. This field acts on the needle, which is a small magnet, and turns it.

2Magnets, magnetic field and field lines

Magnets and the compass

  • A compass needle is a small bar magnet, free to turn.
  • The end that points (roughly) north is the north-seeking pole, or north pole (N). The other end is the south-seeking pole, or south pole (S).
  • Like poles repel; unlike poles attract.
  • A compass needle is deflected near a bar magnet because the magnet’s field exerts forces on the poles of the needle.

Magnetic field

The region round a magnet in which its force can be detected. It has both size (magnitude) and direction.

Activity: iron filings round a bar magnet

  1. Fix a sheet of white paper on a drawing board. Place a bar magnet at its centre.
  2. Sprinkle iron filings evenly round the magnet (a salt-sprinkler helps).
  3. Tap the board gently. The filings line up in a pattern of curves from one pole to the other.
Iron filings sprinkled round a bar magnet on a sheet of paper. After a gentle tap they line up along curved paths from one pole of the magnet to the other: these paths are the magnetic field lines. The filings crowd most thickly at the poles.SN
Figure 2. Iron filings line up along the field lines of a bar magnet.
  • The magnet exerts a force on each filing, so the filings arrange themselves in a pattern.
  • The lines along which they line up are the magnetic field lines.

Magnetic field line

The path along which a free north pole would tend to move. The direction of the field at a point is the direction in which the north pole of a compass needle points there.

Activity: drawing field lines with a compass

  1. Fix a bar magnet on a sheet of paper and mark its outline.
  2. Place a compass near the north pole. Its south pole points towards the magnet’s north pole. Mark both ends of the needle.
  3. Move the compass so that its south pole sits at the mark where its north pole was. Mark again.
  4. Repeat, step by step, until you reach the south pole of the magnet.
  5. Join the marks with a smooth curve: this is one field line. Repeat to draw more lines.
Drawing a field line with a compass. The compass is placed near the north pole of a bar magnet and the positions of the two ends of its needle are marked. It is moved so that its south pole sits where its north pole was, and so on, step by step to the south pole. Joining the marks gives a smooth curve: a magnetic field line. The needle always lies along the line.SNMark both endsof the needleJoin the marks:a field line
Figure 3. Drawing a field line with a compass. The needle always lies along the line.
  • The deflection of the needle is greatest near the poles, where the field is strongest.

Extra The SI unit of magnetic field is the tesla (T). It is not in the textbook.

Remember

  • Magnetic field: region round a magnet where its force can be detected; it has magnitude and direction.
  • Direction of the field at a point = the way the north pole of a compass needle points there.
Quick checkWhy does a compass needle get deflected when brought near a bar magnet?Show answer

The needle is a small magnet. The bar magnet’s field exerts forces on its poles (like poles repel, unlike poles attract), so the needle turns to line up with the field.

3Properties of magnetic field lines

Magnetic field lines of a bar magnet. Outside the magnet they come out of the north pole and curve round into the south pole; inside the magnet they run from the south pole to the north pole, so every line is a closed curve. The lines are crowded near the poles, where the field is strongest, and spread out far from the magnet. No two lines cross.SNInside the magnet: S to NCrowded near the poles: strongFar apart: weaker field
Figure 4. Field lines of a bar magnet: out of the north pole, into the south pole, and from S to N inside.

Properties of magnetic field lines

  1. Outside a magnet, field lines go from the north pole to the south pole.
  2. Inside the magnet, they go from the south pole to the north pole.
  3. So field lines are closed curves.
  4. Where the lines are closer together, the field is stronger (near the poles). Where they are far apart, it is weaker.
  5. No two field lines ever cross each other.
  6. The tangent to a field line at a point gives the direction of the field there.

Why two field lines never cross

  • At a crossing point, the field would have two directions.
  • A compass needle there would have to point two ways at once, which is impossible.

Uniform field

(a) A uniform magnetic field is drawn as parallel, equally spaced straight lines, all pointing the same way. (b) A field that is not uniform: the lines get closer together towards the right, where the field is stronger.(a) Uniform field(b) Non-uniform field
Figure 5. (a) A uniform field: parallel, equally spaced lines. (b) A field that is not uniform.
  • A uniform magnetic field has the same strength and direction everywhere.
  • It is drawn as parallel, equally spaced straight lines, all pointing the same way.

Remember

  • Field lines: N to S outside, S to N inside, so they are closed curves.
  • Crowded lines mean a strong field. Field lines never cross.
  • Uniform field: parallel, equally spaced lines.
Quick checkA student draws two field lines of a bar magnet crossing each other. Why is this wrong?Show answer

At the crossing point the field would have two directions, and a compass needle would point two ways at once. That is impossible, so field lines never cross.

4Field due to a current in a straight conductor

Activity: iron filings round a straight wire

  1. Pass a long, straight, thick copper wire vertically through the centre of a horizontal cardboard sheet.
  2. Connect the wire in series with a battery (12 V), a rheostat, an ammeter and a plug key.
  3. Sprinkle iron filings on the card and switch on the current. Tap the card gently.
  4. The filings form concentric circles centred on the wire.
  5. Place a compass at a point P on a circle. Its north pole gives the direction of the field there.
A straight wire passes upright through a horizontal cardboard sheet. With a current flowing upwards, iron filings on the card form concentric circles centred on the wire. Seen from above, the field lines run anticlockwise. The circles get farther apart away from the wire, where the field is weaker. Compass needles at P, near the wire, and Q, farther away, lie along the circles.PQCurrent (upwards)Concentric circles:field linesCardboard withiron filingsCircles farther apart:field weaker
Figure 6. The field lines round a straight wire are concentric circles, centred on the wire.

Pattern of the field

  • The field lines are concentric circles in planes at right angles to the wire.
  • The circles get farther apart away from the wire: the field becomes weaker.
  • Reverse the current and the direction of the field lines reverses.

What the field depends on

Change madeDeflection of the compassWhat it shows
Increase the currentIncreasesThe field gets stronger as the current increases.
Move the compass farther away (P to Q)DecreasesThe field gets weaker as the distance from the wire increases.
Reverse the currentTurns the other wayThe direction of the field reverses.

So the field of a straight wire is larger for a larger current and smaller at a larger distance from the wire.

Remember

  • Straight wire: field lines are concentric circles round the wire.
  • Field strength increases with the current and decreases with the distance from the wire.
Quick checkA compass is moved away from a current-carrying wire. What happens to its deflection, and why?Show answer

The deflection decreases, because the magnetic field of the wire becomes weaker as the distance from the wire increases.

5Right-hand thumb rule

Right-hand thumb rule

Imagine holding a current-carrying straight conductor in your right hand with the thumb pointing along the current. Your fingers wrap round the conductor in the direction of the magnetic field lines.

The right-hand thumb rule. A right hand grips a straight current-carrying wire with the thumb pointing along the current, upwards. The curled fingers wrap round the wire in the direction of the magnetic field lines: anticlockwise when seen from above.Current (thumb)Thumb points in thedirection of the currentFingers curl in thedirection of the fieldMagnetic field lines
Figure 7. The right-hand thumb rule: thumb along the current, curled fingers along the field.
  • It is also called Maxwell’s corkscrew rule: if a corkscrew is driven forward in the direction of the current, its direction of turning is the direction of the field.
  • The rule works for any part of a wire: a straight wire, a loop or a coil.

Wires drawn end on

Field lines round a straight wire seen end on. (a) The current comes out of the page (dot): the field lines are anticlockwise circles. (b) The current goes into the page (cross): the circles are clockwise. The circles are drawn farther apart away from the wire because the field gets weaker.(a) Current out of the pageField: anticlockwise(b) Current into the pageField: clockwise
Figure 8. A dot means the current comes out of the page; a cross means it goes into the page.
CurrentSymbolField lines (seen by you)
Out of the page (towards you)Dot ⊙Anticlockwise circles
Into the page (away from you)Cross ⊗Clockwise circles

Example: a power line

A horizontal power line carries a current from east to west. Find the field directly below and directly above it.

Example: a power line carries a current from east to west. Seen from its east end the current goes away from you (cross), so the field lines are clockwise circles: the field points south at a point below the wire and north at a point above it.Current: east to westWE(a) Power lineseen from aboveNorthAbove: northBelow: southSN(b) Seen from the east endField lines clockwise
Figure 9. Seen from the east end, the current goes away from you, so the field lines are clockwise.
  • Point the right thumb from east to west. The fingers curl clockwise as seen from the east end, and anticlockwise as seen from the west end.
  • So the field points south at a point directly below the wire.
  • It points north at a point directly above the wire.

Remember

  • Right hand: thumb along the current, fingers curl along the field.
  • Current towards you: anticlockwise field lines. Current away from you: clockwise.
Quick checkA vertical wire carries a current upwards. Seen from above, are the field lines clockwise or anticlockwise?Show answer

Anticlockwise. With the right thumb pointing up, the fingers curl anticlockwise when seen from above.

6Field due to a current in a circular loop

Pattern of the field

Magnetic field lines of a circular loop carrying a current. The loop stands at right angles to the page. Close to the wire the lines are circles round it; towards the centre of the loop they become nearly straight and all point the same way through the loop. One face of the loop acts as a north pole and the other as a south pole.CurrentSNCircles round the wireNearly straight at the centre
Figure 10. Field lines of a current-carrying circular loop, which stands at right angles to the page.
  • Each small part of the loop acts like a short straight wire, with circles round it.
  • Near the wire the circles are small. Towards the centre they become larger and look like straight lines.
  • By the right-hand thumb rule, every part of the loop gives a field in the same direction inside the loop. So the fields add up there.
  • At the centre the field lines are nearly straight and parallel.

A coil of many turns

  • In a coil of n turns, the current goes round the same way in every turn.
  • So the field of the coil is n times the field of one turn.

Factors that increase the field of a loop or coil

More current

The field at a point depends directly on the current.

More turns

A coil of n turns gives n times the field of one turn.

Extra A loop of smaller radius gives a stronger field at its centre.

Activity: a coil through a cardboard

  1. Pass a circular coil of many turns through two holes in a cardboard, at right angles to it.
  2. Connect the coil in series with a battery, a key and a rheostat.
  3. Sprinkle iron filings on the card, plug the key and tap the card. The filings show the pattern in Figure 10.

Extra Look at one face of the loop. If the current goes anticlockwise, that face is a north pole; if clockwise, a south pole.

Remember

  • Circular loop: circles near the wire, nearly straight parallel lines at the centre.
  • All parts of the loop make the field point the same way inside it.
  • Field of a coil increases with the current and the number of turns.
Quick checkA coil has 50 turns. How does its field compare with that of a single turn carrying the same current?Show answer

It is 50 times as large, because the current flows the same way in every turn and the fields of all the turns add up.

7Field due to a current in a solenoid

Solenoid

A coil of many circular turns of insulated copper wire wrapped closely in the shape of a cylinder.

Magnetic field lines of a current-carrying solenoid, a long coil of many turns. Inside the coil the lines are parallel straight lines: the field is uniform. Outside, the lines curve round from one end to the other, as for a bar magnet. The end the lines come out of is a north pole; the other end is a south pole.+−KeyNSInside: parallel lines, uniform field
Figure 11. Field lines of a current-carrying solenoid. Its field is like that of a bar magnet.

Field of a solenoid

  • The pattern of field lines is like that of a bar magnet.
  • One end of the solenoid acts as a north pole and the other as a south pole.
  • Inside, the field lines are parallel straight lines. So the field is the same at all points inside: it is uniform.
  • Outside, the lines go from the north end round to the south end, as for a bar magnet.
  • Reverse the current and the poles change places.

Which end is the north pole?

  • Grip the solenoid in your right hand with the fingers curling along the current in the turns. The thumb points to the north pole.
  • The field inside the solenoid points towards its north end.

Extra Look at an end of the solenoid: anticlockwise current means that end is a north pole; clockwise means a south pole.

Solenoid and bar magnet compared

Current-carrying solenoidBar magnet
Field pattern outsideLike a bar magnetN to S
PolesOne end N, the other SOne end N, the other S
Field insideUniform: parallel linesS to N inside the magnet
Can it be switched off?Yes: no current, no fieldNo (permanent)
Can the poles be reversed?Yes: reverse the currentNo
StrengthChanged by changing the current or the turnsFixed

Remember

  • Solenoid: a long cylindrical coil of insulated copper wire.
  • Its field is like a bar magnet’s; inside it is uniform (parallel lines).
Quick checkThe magnetic field inside a long straight current-carrying solenoid is (a) zero, (b) less near the ends, (c) more near the ends, (d) the same at all points. Which is correct?Show answer

(d) The field lines inside are parallel straight lines, so the field is uniform: the same at all points.

8Electromagnets

Electromagnet

A magnet made by placing a piece of magnetic material, such as soft iron, inside a current-carrying solenoid. It is a core of soft iron wrapped round with a coil of insulated copper wire.

An electromagnet: a soft iron core placed inside a coil of insulated copper wire joined to a cell and a key. When the current flows, the iron becomes a strong magnet, with a north pole at one end and a south pole at the other, and attracts iron pins. When the current is switched off, it loses its magnetism and the pins fall off.+−KeyNSSoft iron coreCoil of insulatedcopper wireIron pins attracted
Figure 12. An electromagnet: a soft iron core inside a coil. It attracts iron pins only while a current flows.
  • The strong field inside the solenoid magnetises the iron core.
  • Soft iron loses its magnetism as soon as the current stops. So the magnet can be switched on and off.
  • A steel rod placed in the coil keeps its magnetism, so it becomes a permanent magnet.

Strength of an electromagnet increases with

More turns

More turns in the coil.

More current

A larger current in the coil.

A soft iron core

The core makes the field much stronger.

Permanent magnet and electromagnet

Permanent (bar) magnetElectromagnet
Made ofSteel or another hard magnetic materialSoft iron core inside a coil
MagnetismPermanentOnly while a current flows
StrengthFixed; usually weakerCan be changed; can be very strong
PolarityFixedReversed by reversing the current

Ways of producing a magnetic field

  • A permanent magnet, such as a bar magnet.
  • A current in a conductor: a straight wire, a loop, a coil or a solenoid.
  • An electromagnet: a current-carrying coil with a soft iron core.

Extra Electromagnets are used in electric bells, cranes that lift scrap iron, loudspeakers and MRI machines.

Remember

  • Electromagnet = soft iron core + coil of insulated copper wire + current.
  • Stronger with more turns, more current and an iron core.
  • It is a magnet only while the current flows.
Quick checkWhy is soft iron, and not steel, used for the core of an electromagnet?Show answer

Soft iron becomes strongly magnetised while the current flows and loses its magnetism when it stops. Steel would stay magnetised, so the magnet could not be switched off.

9Force on a current-carrying conductor in a magnetic field

  • A current-carrying conductor produces a magnetic field, which exerts a force on a magnet nearby.
  • André-Marie Ampère (1775–1836) suggested that the magnet must exert an equal and opposite force on the conductor.

Force on a current in a magnetic field

A current-carrying conductor placed in a magnetic field experiences a force. The force is at right angles to both the current and the field.

Activity: a rod between the poles of a magnet

  1. Hang a small aluminium rod AB (about 5 cm) horizontally from a stand by two connecting wires.
  2. Place a strong horseshoe magnet so that the rod lies between its poles: north pole below, south pole above. The field points upwards.
  3. Connect the rod in series with a battery, a key and a rheostat.
  4. Pass a current from B to A. The rod moves to the left.
  5. Reverse the current. The rod moves to the right.
  6. Swap the poles of the magnet (field downwards). The direction of the force reverses again.
Activity set-up: a short aluminium rod AB hangs from two wires between the poles of a horseshoe magnet, the north pole below and the south pole above, so the magnetic field points upwards. When a current flows through the rod from B to A, the rod is pushed to the left: a force acts on it at right angles to both the current and the field.SNABForceCurrent from B to AField upwards (N below, S above)
Figure 13. The rod AB carries a current between the poles of a horseshoe magnet and is pushed sideways.
The rod seen end on, between a north pole below and a south pole above, so the field points upwards. (a) Current coming towards you: the force on the rod is to the left. (b) Current reversed: the force is to the right.SN(a) Current towards youForce to the leftSN(b) Current reversedForce to the right
Figure 14. The rod seen end on. Reversing the current reverses the force.

What the force depends on

Change madeEffect on the force (or the displacement of the rod)
Reverse the currentDirection of the force reverses
Reverse the field (swap the poles)Direction of the force reverses
Reverse bothDirection stays the same
Increase the currentForce increases: larger displacement
Use a stronger magnetForce increases: larger displacement
Use a longer rod (more of it in the field)Force increases: larger displacement
  • The force is largest when the current is at right angles to the field.

Extra The force is zero when the current is parallel to the field.

Remember

  • A current in a magnetic field feels a force at right angles to both.
  • Reversing the current or the field reverses the force.
  • The force is largest when the current is at right angles to the field.
Quick checkIn the rod activity, what happens if both the current and the magnet’s poles are reversed together?Show answer

The force keeps its original direction: each change reverses it, so two changes cancel out.

10Fleming’s left-hand rule

Fleming’s left-hand rule

Stretch the thumb, forefinger and middle finger of your left hand so that they are at right angles to each other. If the first finger points along the magnetic field and the second finger along the current, then the thumb points in the direction of the motion or force on the conductor.

Fleming’s left-hand rule. The thumb, first finger and second finger of the left hand are stretched at right angles to each other. The first finger points along the magnetic field, the second finger along the current, and then the thumb points along the force on the conductor, which is the direction it moves. Here the field is upwards, the current comes towards you and the force is to the left.First finger: field (B)Thumb: forceor motion (F)Second finger:current (I)FieldForceCurrentAll three atright angles
Figure 15. Fleming’s left-hand rule: First finger Field, seCond finger Current, thuMb Motion.
Finger (left hand)Shows the direction of
First finger (forefinger)Field (magnetic field)
Second finger (middle finger)Current
ThumbMotion, or force, on the conductor

Using the rule

  1. Point the first finger along the field: from the N pole towards the S pole.
  2. Turn your hand so that the second finger points along the current (from + to −).
  3. The thumb then gives the direction of the force, and of the motion.

Moving charges

  • A beam of moving charges is also a current, so it feels a force in a magnetic field.
  • The direction of current is the direction in which positive charges move. It is opposite to the motion of electrons.
  • The magnetic force is at right angles to the motion. It changes the direction of motion, so it changes the velocity and the momentum, but not the speed or the mass.
An electron moves down the page through a magnetic field that points to the right. The current is opposite to the motion of the electron, up the page. By Fleming’s left-hand rule the force on the electron is into the page.Electron−FieldField: to the rightElectron: down the pageCurrent: up the pageForce: into the page
Figure 16. An electron moves down the page in a field pointing to the right. The force on it is into the page.

Example: an electron enters a magnetic field at right angles, as in Figure 16. The current is opposite to its motion, so it is up the page. With the first finger to the right and the second finger up the page, the thumb points into the page.

Devices that use this force

Electric motors, electric generators, loudspeakers, microphones and measuring instruments use current-carrying conductors and magnetic fields.

Extra Fleming’s right-hand rule gives the direction of the current induced in a conductor (such as a coil in a generator) that moves in a magnetic field. Right hand, fingers at right angles: thumb along the motion, first finger along the field, second finger along the induced current.

Remember

  • Left hand: First finger Field, seCond finger Current, thuMb Motion (force).
  • For electrons, take the current opposite to their motion.
  • A magnetic force changes the direction of motion, not the speed.
Quick checkA positively charged particle moving west is pushed north by a magnetic field. Which way does the field point?Show answer

Upwards. The current is west (the way the positive charge moves) and the force is north. By Fleming’s left-hand rule the first finger then points vertically upwards.

Try it yourselfSwitch on the current in a wire, a loop and a solenoid and watch the field lines and compass needles, push a rod with a magnetic force and check it with your left hand, and see a fuse melt when a circuit is overloaded, in the magnetism lab.

11Magnetism in medicine

  • An electric current always produces a magnetic field.
  • Even the weak ion currents along the nerve cells in our body produce magnetic fields.
  • When we touch something, our nerves carry an electric impulse to the muscles. This impulse produces a temporary magnetic field.
  • These fields are very weak: about one-billionth of the Earth’s magnetic field.
  • The two organs where the magnetic field produced is significant are the heart and the brain.

MRI (Magnetic Resonance Imaging)

A technique that uses magnetism to obtain images of the parts inside the body. Doctors study these images to diagnose illness.

Remember

  • Nerve impulses are tiny currents, so they make tiny magnetic fields.
  • Heart and brain: the organs with a significant magnetic field.
  • MRI uses magnetism to make images of body parts for diagnosis.
Quick checkName the two organs of the human body where the magnetic field produced is significant.Show answer

The heart and the brain.

12Domestic electric circuits

The mains supply

  • Electric power comes to our homes from the mains, through overhead poles or underground cables.
  • In India the supply is AC (alternating current) at 220 V and 50 Hz.
  • AC keeps reversing its direction; 50 Hz means it goes through 50 complete cycles each second. A cell or battery gives DC (direct current), which flows one way only.
WireInsulation colourWhat it does
Live wire (positive)RedBrings the current in. It is at 220 V with respect to the neutral wire.
Neutral wire (negative)BlackCompletes the circuit: the current returns through it.
Earth wireGreenA safety wire, joined to a metal plate deep in the earth near the house.

From the pole to the appliances

  1. Mains
  2. Electricity board’s fuse (main fuse)
  3. Electricity meter
  4. Main switch
  5. Fuse for each circuit
  6. Separate circuits
  7. Appliances
A common domestic circuit. The live wire (red), neutral wire (black) and earth wire (green) come in from the mains. The live wire passes through the electricity board’s fuse; the live and neutral wires pass through the electricity meter and the distribution box, which holds the main switch and a fuse for each circuit. The appliances are joined in parallel between the live and neutral wires, 220 V apart, each with its own switch on the live wire. Metal-bodied appliances are joined to the earth wire, which goes to a metal plate buried in the earth.Earth wire (green)Live (red)Neutral (black)Main fuseMeterDistribution box(main switch, fuses)220 VFanIronAppliances in parallelSwitchEarth plate
Figure 17. A common domestic circuit: live (red), neutral (black) and earth (green) wires.
  • At the meter-board, the live and neutral wires pass through the main fuse into the electricity meter.
  • Through the main switch in the distribution box, they connect to the line wires that feed separate circuits.

Two separate circuits

CircuitCurrent ratingUsed for
Power circuit15 AAppliances with higher power, such as geysers and air coolers
Lighting circuit5 ABulbs, fans and other low-power appliances

Appliances are joined in parallel

  • Each appliance is connected across the live and neutral wires, parallel to the others.
  • So every appliance gets the same potential difference (220 V).
  • Each has its own switch, so it can be turned on or off on its own.
  • If one appliance stops working, the others still work.

Extra Switches and fuses are put in the live wire, so that an appliance that is switched off is cut off from the live wire.

Remember

  • Live: red, 220 V. Neutral: black. Earth: green, a safety wire.
  • Order: main fuse, meter, main switch (distribution box), fuses, circuits.
  • 15 A circuit for high-power appliances; 5 A circuit for bulbs and fans.
  • Appliances are in parallel: same voltage, separate switches.
Quick checkWhy are household appliances connected in parallel and not in series?Show answer

In parallel each appliance gets the full 220 V and can be switched on or off on its own. If one fails, the others keep working.

13The earth wire and earthing

Earth wire

A wire with green insulation, connected to a metal plate buried deep in the earth near the house. It is a safety measure.

Earthing. The metal body of an appliance is joined by the green earth wire to a metal plate buried in the ground. If a fault lets the live wire touch the body, the current flows through the low-resistance earth wire into the ground instead of through a person; the body stays at the potential of the earth, and the large current usually blows the fuse.FuseLiveNeutralMetal bodyEarth wireLarge currentto earthMetal plate in the earthFault: live wire touches the body
Figure 18. If the live wire touches the metal body, the current flows to the earth through the earth wire.

How earthing protects us

  1. The metal body of an appliance is connected to the earth wire.
  2. The earth wire gives a low-resistance path for the current.
  3. If current leaks to the body (a fault), it flows through the earth wire into the ground.
  4. The body stays at the potential of the earth (zero), so the user does not get a severe electric shock.
  • Earthing is needed most for appliances with a metal body, such as an electric press (iron), toaster, table fan and refrigerator.
  • The large current through the earth wire usually also melts the fuse, cutting off the supply.

Remember

  • Earth wire: green; joined to a metal plate deep in the earth.
  • It gives a low-resistance path, keeping the metal body at earth potential.
  • It protects the user from a severe shock if current leaks to the body.
Quick checkWhy is it necessary to earth metallic appliances?Show answer

If the live wire touches the metal body, the leaking current flows safely to the earth through the low-resistance earth wire. The body stays at earth potential, so a person who touches it does not get a severe shock.

14Short circuit, overloading and the fuse

Short circuit

When the live wire and the neutral wire come into direct contact, the resistance of the circuit becomes almost zero and the current increases suddenly to a very large value.

Overloading

When a circuit carries more current than it is rated for.

(a) Short circuit: the bare live and neutral wires touch, so the resistance of the circuit becomes almost zero and a very large current flows; the fuse melts. (b) Overloading: too many appliances on one circuit draw currents that add up to more than the rating of the circuit; the fuse melts.Fuse melts(a) Short circuitLive and neutral touch:resistance nearly zero,current very largeFuse meltsI₁I₂I₃I₄(b) OverloadingToo many appliances onone circuit: total currentmore than its rating
Figure 19. (a) Short circuit: live and neutral touch. (b) Overloading: too many appliances on one circuit.

Causes

Short circuitOverloading
What happensLive and neutral wires touch directlyThe total current is more than the rating of the circuit
CausesDamaged insulation of the wires, or a fault in an applianceToo many appliances on one socket; an accidental rise in the supply voltage; a short circuit
ResultCurrent rises suddenly to a very large valueCurrent rises above the safe limit
DangerWires heat up: sparks, fire, damageWires overheat: fire, damage to appliances

The electric fuse

  • A fuse is the most important safety device in a domestic circuit. It protects the circuit and the appliances from damage due to short circuits and overloading.
  • It is a short wire of low melting point, joined in series in the live wire.
  • When an unduly high current flows, Joule heating in the fuse wire melts it. This breaks the circuit and stops the current.

Worked example 1

An electric oven of 2 kW is used on a 220 V domestic circuit of current rating 5 A. What happens?

Given
P = 2 kW = 2000 WV = 220 V
Find
Current I

Solution

I=PV=2000 W220 V≈9.1 A

The oven draws about 9.1 A, more than the 5 A rating. The circuit is overloaded: the fuse melts and cuts off the supply.

Precautions against overloading

  • Do not connect too many appliances to a single socket.
  • Use high-power appliances (geysers, heaters, ovens) only on the 15 A circuit.
  • Use a fuse of the correct rating in each circuit.
  • Do not use appliances at the same time if together they draw more than the rated current.

Safety measures in electric circuits

Electric fuse

Melts and breaks the circuit when the current is too large.

Earthing

Takes leaking current safely to the earth, preventing severe shocks.

Extra Many homes now use MCBs (miniature circuit breakers), switches that turn off by themselves when the current is too large. They are reset instead of replaced.

Remember

  • Short circuit: live touches neutral, resistance nearly zero, current very large.
  • Overloading: too much current for the circuit; often too many appliances on one socket.
  • The fuse wire melts (Joule heating) and breaks the circuit.
Quick checkAt the time of a short circuit, what happens to the current in the circuit?Show answer

It increases heavily, because the resistance of the circuit becomes almost zero.

Test yourselfTake the 25-question practice quiz on this chapter. Revising for the board exam?Get the Chapter 12 revision PDF: quick notes, 20 new board-pattern questions and full answers, for ₹49.