Chapter 11 · Physics

Electricity

How electric charges move through a circuit, what controls the current, and how electrical energy turns into heat.

Revising? See every formula in this chapter on one page, and try the simulator.
In this chapter 8 topics
  1. 1Electric charge and current
  2. 2Potential difference
  3. 3Circuit diagrams
  4. 4Ohm’s law
  5. 5What resistance depends on
  6. 6Resistors in series and in parallel
  7. 7Heating effect of electric current
  8. 8Electric power

1Electric charge and current

Switch on a torch and its bulb lights up almost at once. Tiny charged particles start moving through the wires and the bulb. This flow of charge is called electric current.

Electric charge

Charge is a basic property of matter, just like mass. Its SI unit is the coulomb (C). In a metal wire, the charges that move are electrons. Each electron carries a tiny negative charge of 1.6 × 10−19 C.

Definition

Electric current is the rate of flow of electric charge through a conductor. It tells us how much charge passes a point in the conductor every second.

Formula

I = Qt

where

  • Ielectric currentampere (A)
  • Qcharge that flowscoulomb (C)
  • ttime takensecond (s)

The SI unit of current is the ampere (A). When 1 coulomb of charge flows past a point in 1 second, the current is 1 ampere:

1 A=1 C1 s

Small currents are measured in milliamperes and microamperes: 1 mA = 10−3 A and 1 µA = 10−6 A. Current is measured with an ammeter, which is always joined in series in the circuit.

Which way does current flow?

By agreement, current flows from the positive terminal of a cell, round the circuit, to the negative terminal. This is called conventional current. Electrons actually move the other way, from negative to positive.

Electric circuit

A continuous, closed path along which current flows is an electric circuit. If the path breaks anywhere, for example when a switch is turned off, the current stops everywhere in the circuit.

A cell, a closed switch, a bulb and an ammeter joined in one loop. Current flows out of the positive terminal, round the circuit and back to the negative terminal. Electrons flow the opposite way. +− Cell Bulb A Ammeter Switch (closed) Current Electron flow
Figure 1. A simple circuit. Current flows from + to − round the circuit; electrons flow the opposite way.

Worked example 1

A current of 0.5 A flows through a bulb for 10 minutes. How much charge flows through the bulb?

Given
I = 0.5 At = 10 min = 600 s
Find
Charge, Q

Solution

Q=I × t=0.5 A × 600 s=300 C

The charge that flows through the bulb is 300 C.

Worked example 2

A wire carries a current of 1.6 mA. How many electrons pass a point in the wire every second?

Given
I = 1.6 mA = 1.6 × 10−3 At = 1 scharge on one electron, e = 1.6 × 10−19 C
Find
Number of electrons, n

Solution

Q=I × t=1.6 × 10−3 A × 1 s=1.6 × 10−3 Cn=Qe=1.6 × 10−3 C1.6 × 10−19 C=1016

1016 electrons pass the point every second.

Remember

  • Current is the charge flowing per second. Its unit is the ampere (A).
  • An ammeter measures current and is always joined in series.
  • Conventional current flows from + to −. Electrons flow from − to +.
Quick checkIf 120 C of charge flows through a wire in 1 minute, what is the current?Show answer
I=Qt=120 C60 s=2 A

2Potential difference

Water flows through a pipe only when there is a difference in pressure between its two ends. In the same way, charges flow through a wire only when there is a difference in electric potential between its two ends.

A cell creates this difference. Chemical reactions inside the cell keep one terminal at a higher potential than the other, even while current is flowing. To do this, the cell uses up the chemical energy stored in it.

Definition

The potential difference between two points in a circuit is the work done to move a unit charge from one point to the other.

Formula

V = WQ

where

  • Vpotential differencevolt (V)
  • Wwork donejoule (J)
  • Qcharge movedcoulomb (C)

The SI unit of potential difference is the volt (V). The potential difference between two points is 1 volt when 1 joule of work is done to move 1 coulomb of charge from one point to the other:

1 V=1 J1 C

Potential difference is measured with a voltmeter, which is always joined in parallel across the two points.

Worked example 3

A charge of 4 C moves between two points that have a potential difference of 12 V. How much work is done?

Given
V = 12 VQ = 4 C
Find
Work done, W

Solution

W=V × Q=12 V × 4 C=48 J

The work done is 48 J.

Remember

  • A cell’s voltage is the energy it gives to each coulomb of charge. A 1.5 V cell gives 1.5 J to every coulomb.
  • A voltmeter measures potential difference and is always joined in parallel.
Quick checkHow much work is done in moving 2 C of charge across a potential difference of 9 V?Show answer
W=V × Q=9 V × 2 C=18 J

3Circuit diagrams

Drawing real wires, bulbs and cells takes a long time. So we use simple standard symbols instead. A drawing made with these symbols is called a circuit diagram. Anyone who knows the symbols can read it.

  • Connecting wireJoins the parts of a circuit.
  • CellThe longer line is the positive (+) terminal.
  • BatteryTwo or more cells joined together.
  • Switch, openAlso called a plug key. No current flows.
  • Switch, closedThe circuit is complete, so current flows.
  • Wires joinedA dot shows the wires are connected.
  • Wires crossingNo dot: the wires pass over each other without joining.
  • Electric bulbGlows when current flows through it.
  • ResistorHas a fixed resistance.
  • RheostatA variable resistor. The arrow shows its resistance can be changed.
  • AmmeterMeasures current. Always joined in series.
  • VoltmeterMeasures potential difference. Always joined in parallel.
Figure 2. Common symbols used in circuit diagrams.

Joining meters correctly

An ammeter is joined in series, so that all the current passes through it. It has a very low resistance, so it hardly changes the current it measures.

A voltmeter is joined in parallel, across the part being measured. It has a very high resistance, so it takes almost no current from the circuit.

A battery, a switch, an ammeter, a rheostat and a resistor R joined in series. A voltmeter is joined in parallel across the resistor R. +− Battery Switch A Ammeter Rheostat Resistor R V Voltmeter I
Figure 3. An ammeter in series and a voltmeter in parallel across the resistor R. The rheostat is used to change the current.

Remember

  • A dot means wires are joined. No dot means they only cross.
  • Never join an ammeter directly across a cell. Its very low resistance lets a large current flow, which can damage it.
Quick checkIn Figure 3, which meter would show a reading if the switch were open, and why?Show answer

Neither. With the switch open, the circuit is broken, so no current flows anywhere. The ammeter reads zero, and there is no potential difference across the resistor for the voltmeter to show.

4Ohm’s law

In 1827, the German physicist Georg Simon Ohm found a simple link between the current through a metal wire and the potential difference across it. It is now called Ohm’s law.

Ohm’s law

The current through a metallic conductor is directly proportional to the potential difference across its ends, provided its temperature stays the same.

If V is the potential difference and I is the current, then V ∝ I, which we write as V = IR. The constant R is the resistance of the conductor.

Formula

R = VI

where

  • Rresistanceohm (Ω)
  • Vpotential differencevolt (V)
  • Icurrentampere (A)

Resistance is the property of a conductor that opposes the flow of current through it. For the same potential difference, a larger resistance means a smaller current. A conductor has a resistance of 1 ohm when a potential difference of 1 volt across it drives a current of 1 ampere:

1 Ω=1 V1 A

The V–I graph

Measure the potential difference and the current for a metal wire at several settings of the rheostat, then plot the readings. The points lie on a straight line that passes through the origin. With V on the vertical axis and I on the horizontal axis, the slope of this line is the resistance of the wire.

Graph of potential difference V against current I for a 10 ohm resistor. The points 0.1 A and 1 V, 0.2 A and 2 V, 0.3 A and 3 V, and 0.4 A and 4 V lie on a straight line through the origin. The slope, 2 V for every 0.2 A, equals the resistance, 10 ohms. 0.10.20.30.40.5123450 ΔI = 0.2 A ΔV = 2 V R = ΔVΔI = 10 Ω Current, I (in A) Potential difference, V (in V)
Figure 4. V–I graph for a 10 Ω resistor. A straight line through the origin shows that V is proportional to I.

A rheostat is a resistor whose resistance can be changed. It lets us change the current in a circuit without changing the battery.

Worked example 4

A torch bulb draws a current of 0.3 A from a 3 V battery. What is the resistance of its filament?

Given
V = 3 VI = 0.3 A
Find
Resistance, R

Solution

R=VI=3 V0.3 A=10 Ω

The resistance of the filament is 10 Ω.

Worked example 5

An electric heater has a resistance of 44 Ω. What current flows through it on a 220 V supply?

Given
R = 44 ΩV = 220 V
Find
Current, I

Solution

I=VR=220 V44 Ω=5 A

A current of 5 A flows through the heater.

Remember

  • Ohm’s law works only when the temperature of the conductor stays the same.
  • A bulb filament gets very hot, so its resistance rises as the current increases.
  • With V on the vertical axis and I on the horizontal axis, the slope of the graph is the resistance. If the axes are swapped, the slope is the reciprocal of the resistance.
Quick checkThe potential difference across a resistor is doubled, and its temperature stays the same. What happens to the current?Show answer

The current also doubles. By Ohm’s law, current is directly proportional to potential difference when the resistance does not change.

Try it yourselfSet the voltage, choose a resistor and watch the current change in the Ohm’s law lab.

5What resistance depends on

Every conductor has some resistance, but not the same amount. The resistance of a wire depends on its length, its area of cross-section (how thick it is) and the material it is made of. It also changes with temperature.

Finding out by experiment

Join a cell, a switch and an ammeter in a circuit that has two terminals, X and Y (Figure 5). Connect different wires between X and Y, one at a time, and note the ammeter reading each time. The cell stays the same, so a smaller current means a larger resistance.

A cell, a closed switch and an ammeter joined in a loop that has two terminals, X and Y. A test wire is joined between X and Y. +− Cell Switch A Ammeter XY Test wire I
Figure 5. Join different wires between X and Y, one at a time. With the same cell, a smaller current means a larger resistance.
  • Length. Take a wire of the same material and thickness, but twice as long. The current falls to half, so the resistance has doubled.
  • Area of cross-section. Take a wire of the same material and length, but with twice the area of cross-section. The current doubles, so the resistance has halved.
  • Material. Take a wire of another material with the same length and thickness. The current is different, so resistance also depends on the material.

So the resistance of a wire is directly proportional to its length, R ∝ l, and inversely proportional to its area of cross-section, R ∝ 1A. Putting the two together:

Formula

R = ρlA

where

  • Rresistance of the wireohm (Ω)
  • ρresistivity of the materialohm metre (Ω m)
  • llength of the wiremetre (m)
  • Aarea of cross-sectionsquare metre (m²)

Resistivity

The constant ρ (the Greek letter rho) is the resistivity of the material. It equals the resistance of a piece of the material that is 1 m long and has an area of cross-section of 1 m2. Resistivity depends on the material and on its temperature, but not on the length or thickness of the wire.

Rearranging the formula gives ρ = RAl, so the SI unit of resistivity is

unit of ρ=Ω × m2m=Ω m

which is read as the ohm metre.

Resistivity of some materials

The lower the resistivity, the better a material conducts electricity. The table gives approximate values at room temperature, about 20 °C.

MaterialTypeResistivity (in Ω m)
SilverMetal1.6 × 10−8
CopperMetal1.7 × 10−8
AluminiumMetal2.7 × 10−8
TungstenMetal5.6 × 10−8
IronMetal9.7 × 10−8
MercuryMetal (liquid)9.6 × 10−7
NichromeAlloy100 × 10−6
GlassInsulator1010 to 1014
RubberInsulator1013 to 1016

Values differ slightly from one book to another, because no two samples of a material are exactly alike.

Metals have very low resistivities, so they are good conductors. Silver is the best conductor of all, but it is costly. Alloys such as nichrome have higher resistivities than the pure metals they are made from. Glass and rubber have enormous resistivities, which is why they are used as insulators. The resistivity of a metal also rises as it gets hotter.

Choosing the right material

  • Connecting wires and power cables are made of copper or aluminium. Their low resistivity means that little energy is wasted as heat in the wires.
  • Heating elements in irons, toasters and kettles are made of an alloy such as nichrome. Alloys have a high resistivity, and they do not oxidise (burn) easily, even when red hot.
  • Bulb filaments are made of tungsten. Its melting point is very high, above 3000 °C, so it can glow white hot without melting.

Before using the formula, change every length into metres and every area into square metres. Since 1 mm = 10−3 m, 1 mm2 = 10−6 m2.

Worked example 6

A copper wire is 20 m long and has an area of cross-section of 1 mm2. Find its resistance. The resistivity of copper is 1.7 × 10−8 Ω m.

Given
l = 20 mA = 1 mm2 = 1 × 10−6 m2ρ = 1.7 × 10−8 Ω m
Find
Resistance, R

Solution

R=ρlA=1.7 × 10−8 Ω m × 20 m1 × 10−6 m2=0.34 Ω

The resistance of the wire is 0.34 Ω.

Worked example 7

A metal wire 2.5 m long has an area of cross-section of 0.5 mm2 and a resistance of 0.135 Ω. Find the resistivity of the metal. Which metal in the table could it be?

Given
l = 2.5 mA = 0.5 mm2 = 5 × 10−7 m2R = 0.135 Ω
Find
Resistivity, ρ

Solution

ρ=RAl=0.135 Ω × 5 × 10−7 m22.5 m=2.7 × 10−8 Ω m

The resistivity is 2.7 × 10−8 Ω m, so the metal is most likely aluminium.

Worked example 8

Wire 1 has a resistance of 8 Ω. Wire 2 is made of the same metal, but it is twice as long and has twice the diameter. Find the resistance of wire 2.

Given
Wire 1: length l, area A, R1 = 8 ΩWire 2: length 2l, diameter doubledDoubling the diameter doubles the radius r, so the area πr2 becomes 4 times larger: 4A
Find
Resistance of wire 2, R2

Solution

R1=ρlA=8 ΩR2=ρ × 2l4A=12 × ρlA=12 × 8 Ω=4 Ω

The resistance of wire 2 is 4 Ω. Twice the length doubles the resistance, but four times the area makes it four times smaller, so overall it halves.

Remember

  • R ∝ l: a longer wire has more resistance.
  • R ∝ 1A: a thicker wire has less resistance.
  • Resistivity depends only on the material and its temperature. Its SI unit is the ohm metre (Ω m).
  • Connecting wires: copper or aluminium. Heating elements: alloys such as nichrome. Bulb filaments: tungsten.
Quick checkA wire of resistance 10 Ω is cut into two equal halves. What is the resistance of each half?Show answer

5 Ω. Each half has half the length, with the same thickness and material, and resistance is proportional to length.

6Resistors in series and in parallel

Most circuits have more than one resistor. Resistors can be joined in two basic ways: one after another, in series, or side by side between the same two points, in parallel.

Equivalent resistance

The equivalent resistance of a group of resistors is the single resistance that could replace the whole group and still draw the same current from the same battery.

Resistors in series

In series, resistors are joined end to end, so there is only one path for the current (Figure 6).

A battery, a closed switch and an ammeter joined in series with three resistors, R1, R2 and R3, placed one after another. The potential differences across the resistors are V1, V2 and V3. +− Battery Switch A R1R2R3V1V2V3 I I
Figure 6. Three resistors in series. The same current flows through each one, and the potential difference of the battery is shared between them.
  • The same current I flows through every resistor. An ammeter gives the same reading wherever it is placed in the circuit.
  • The potential difference V of the battery is shared between the resistors: V = V1 + V2 + V3.

By Ohm’s law, V1 = IR1, V2 = IR2 and V3 = IR3. If the equivalent resistance is Rs, then V = IRs. So

IRs=IR1 + IR2 + IR3Rs=R1 + R2 + R3

Both sides were divided by I to get the second line.

Formula

Rs = R1 + R2 + R3

where

  • Rsequivalent resistance in seriesohm (Ω)
  • R1, R2, R3the separate resistancesohm (Ω)

The equivalent resistance in series is always more than the largest of the separate resistances. So every resistor added in series makes the current smaller.

Worked example 9

Resistors of 2 Ω, 3 Ω and 5 Ω are joined in series to a 12 V battery. Find (a) the equivalent resistance, (b) the current, and (c) the potential difference across each resistor.

Given
R1 = 2 Ω, R2 = 3 Ω, R3 = 5 ΩV = 12 V
Find
Rs, I, and V1, V2, V3

Solution

Rs=R1 + R2 + R3=2 Ω + 3 Ω + 5 Ω=10 ΩI=VRs=12 V10 Ω=1.2 AV1=IR1=1.2 A × 2 Ω=2.4 VV2=1.2 A × 3 Ω=3.6 VV3=1.2 A × 5 Ω=6 V

(a) 10 Ω (b) 1.2 A (c) 2.4 V, 3.6 V and 6 V. Check: 2.4 V + 3.6 V + 6 V = 12 V, the voltage of the battery.

Resistors in parallel

In parallel, each resistor is joined between the same two points, X and Y (Figure 7). The current now has more than one path.

A battery, a closed switch and an ammeter joined to three resistors, R1, R2 and R3, which are in parallel between the points X and Y. The main current I divides into the branch currents I1, I2 and I3. +− Battery Switch A R1I1R2I2R3I3 XY I I
Figure 7. Three resistors in parallel between X and Y. Each has the same potential difference across it, and the main current divides between them.
  • Every resistor has the same potential difference V across it.
  • The main current I divides between the branches: I = I1 + I2 + I3.

By Ohm’s law, the branch currents are I1 = VR1, I2 = VR2 and I3 = VR3. If the equivalent resistance is Rp, then I = VRp. So

VRp=VR1 + VR2 + VR31Rp=1R1 + 1R2 + 1R3

Both sides were divided by V to get the second line.

Formula

1Rp = 1R1 + 1R2 + 1R3

where

  • Rpequivalent resistance in parallelohm (Ω)
  • R1, R2, R3the separate resistancesohm (Ω)

The equivalent resistance in parallel is always less than the smallest of the separate resistances. Every branch added gives the current one more path, so the total current from the battery increases.

For just two resistors in parallel, the formula works out to Rp = R1R2R1 + R2, their product divided by their sum.

Worked example 10

Resistors of 3 Ω and 6 Ω are joined in parallel to a 6 V battery. Find (a) the equivalent resistance, (b) the current from the battery, and (c) the current in each resistor.

Given
R1 = 3 Ω, R2 = 6 ΩV = 6 V
Find
Rp, I, and I1, I2

Solution

1Rp=1R1 + 1R2=13 Ω + 16 Ω=2 + 16 Ω=36 Ω=12 ΩRp=2 ΩI=VRp=6 V2 Ω=3 AI1=VR1=6 V3 Ω=2 AI2=6 V6 Ω=1 A

(a) 2 Ω (b) 3 A (c) 2 A through the 3 Ω resistor and 1 A through the 6 Ω resistor. Check: 2 A + 1 A = 3 A. The smaller resistance carries the larger current.

Series and parallel compared

FeatureIn seriesIn parallel
CurrentThe same through every resistorDivides between the branches
Potential differenceShared between the resistorsThe same across every resistor
Equivalent resistanceMore than the largest resistanceLess than the smallest resistance
If one resistor breaksThe whole circuit stopsThe other branches keep working

Why homes are wired in parallel

The lights, fans and other appliances in a house are joined in parallel with each other. This way:

  • every appliance gets the full supply voltage of 220 V;
  • each appliance can be switched on or off without affecting the others;
  • if one appliance stops working, the others carry on;
  • each appliance draws only the current it needs, which depends on its own resistance.

If the appliances were joined in series, the supply voltage would be shared between them, so none would get the 220 V it is made for, and a single fault would switch everything off.

Series and parallel together

Many circuits use both. Work them out in steps, from the inside out: first add any resistors that are in series within a branch, then replace each parallel group by its equivalent resistance, and finally add the resistances that are left in series.

A 12 volt battery joined to a 2 ohm resistor R1 in series with a parallel pair of resistors between the points X and Y: R2 of 6 ohms and R3 of 3 ohms. +− 12 V R1 = 2 Ω R2 = 6 Ω R3 = 3 Ω XY I
Figure 8. A 2 Ω resistor in series with a parallel pair of 6 Ω and 3 Ω resistors, joined to a 12 V battery.

In the working below, R is the total resistance of the circuit and Vp is the potential difference across the parallel pair.

Worked example 11

In the circuit of Figure 8, find the current from the battery and the current through the 6 Ω resistor.

Given
R1 = 2 Ω, in seriesR2 = 6 Ω and R3 = 3 Ω, in parallelV = 12 V
Find
Current I from the battery, and current I2 through R2

Solution

1Rp=1R2 + 1R3=16 Ω + 13 Ω=1 + 26 Ω=36 Ω=12 ΩRp=2 ΩR=R1 + Rp=2 Ω + 2 Ω=4 ΩI=VR=12 V4 Ω=3 AVp=IRp=3 A × 2 Ω=6 VI2=VpR2=6 V6 Ω=1 A

The battery supplies 3 A. The 6 Ω resistor carries 1 A, and the 3 Ω resistor carries the other 2 A.

Remember

  • In series, the same current flows through every resistor, and Rs = R1 + R2 + R3.
  • In parallel, every resistor has the same potential difference, and 1Rp = 1R1 + 1R2 + 1R3.
  • For n equal resistors, each of resistance R: in series the total is nR; in parallel it is Rn.
  • Household appliances are joined in parallel.
Quick checkYou have three 6 Ω resistors. How would you join them to get (a) 18 Ω, (b) 2 Ω, (c) 9 Ω?Show answer

(a) Join all three in series.

Rs=6 Ω + 6 Ω + 6 Ω=18 Ω

(b) Join all three in parallel.

1Rp=16 Ω + 16 Ω + 16 Ω=36 Ω=12 ΩRp=2 Ω

(c) Join two of them in parallel, which gives 3 Ω, then join the third in series with the pair.

R=3 Ω + 6 Ω=9 Ω

7Heating effect of electric current

An electric iron gets hot within a minute of being switched on, and a phone charger feels warm after some time. In both, an electric current is producing heat. This is the heating effect of electric current.

Where the energy goes

A battery or the mains supply does work to keep charges moving round a circuit. In a fan, part of this energy turns the blades. In a resistor, the energy is changed into heat. If a circuit has only resistors in it, all the energy supplied becomes heat.

How much heat is produced?

Suppose a current I flows for a time t through a resistor of resistance R, and the potential difference across it is V. The charge that flows is Q = It. The work done to move this charge through the potential difference V is

W=VQ=VIt

All of this energy appears as heat H in the resistor. By Ohm’s law, V = IR, so

H=VIt=IR × It=I2Rt

Formula

H = I2Rt

where

  • Hheat producedjoule (J)
  • Icurrentampere (A)
  • Rresistanceohm (Ω)
  • ttimesecond (s)

Joule’s law of heating

The heat produced in a resistor is directly proportional to the square of the current, for a given resistance; to the resistance, for a given current; and to the time for which the current flows.

Because the current is squared, doubling the current produces four times as much heat in the same time.

Worked example 12

A heater coil of resistance 50 Ω carries a current of 4 A. How much heat does it produce in 2 minutes?

Given
R = 50 ΩI = 4 At = 2 min = 120 s
Find
Heat produced, H

Solution

H=I2Rt=(4 A)2 × 50 Ω × 120 s=16 × 50 × 120 J=96 000 J=9.6 × 104 J

The coil produces 9.6 × 104 J of heat.

Worked example 13

A resistor produces 1080 J of heat in 1 minute when a current of 3 A flows through it. Find its resistance.

Given
H = 1080 JI = 3 At = 1 min = 60 s
Find
Resistance, R

Solution

R=HI2t=1080 J(3 A)2 × 60 s=1080540 Ω=2 Ω

The resistance is 2 Ω.

Uses of the heating effect

  • Heating appliances. An electric iron, toaster, kettle, room heater and geyser each have a heating element: a coil of an alloy such as nichrome. The current through the coil produces the heat.
  • Electric bulb. The thin tungsten filament gets so hot that it glows and gives out light, but most of the energy still comes out as heat. The bulb is filled with an unreactive gas such as nitrogen or argon, so that the hot filament does not burn away quickly.
  • Electric fuse. A safety device that uses the heating effect to protect a circuit, as explained below.

The heating effect is not always wanted. Heat produced in connecting wires, computers and motors is wasted energy, and too much of it can damage the parts of a circuit.

The electric fuse

A fuse is a short piece of wire made of a metal or an alloy that melts at a fairly low temperature. In a cartridge fuse, this wire is held inside a porcelain or glass case, with metal caps at both ends (Figure 9). The fuse is always joined in series with the circuit or appliance it protects, so that all the current passes through it.

A cartridge fuse. A thin fuse wire runs inside a porcelain or glass case, between two metal caps that join it to the circuit. Metal cap Fuse wire Porcelain or glass case
Figure 9. A cartridge fuse. The thin fuse wire melts and breaks the circuit if the current becomes too large.

If too much current flows, for example because of a fault or because too many appliances are switched on together, the fuse wire heats up quickly and melts. This breaks the circuit and stops the current before the wiring or the appliance can overheat or catch fire.

Fuses are made for different currents, such as 1 A, 2 A, 3 A, 5 A and 10 A. The fuse chosen should be rated a little above the normal current of the appliance. Worked example 14, in the next topic, shows how to choose one.

Remember

  • Heat produced: H = I2Rt. Doubling the current gives four times the heat.
  • Heating elements are made of alloys such as nichrome. Bulb filaments are made of tungsten.
  • A fuse wire melts when the current is too large. A fuse is always joined in series.
Quick checkThe current through a resistor is made three times as large, and its resistance stays the same. How many times as much heat is produced in the same time?Show answer

Nine times as much. Heat is proportional to the square of the current, and 32 = 9.

8Electric power

A 1000 W electric iron gets hot far faster than a 10 W night lamp gets warm. The difference is their power: how quickly each one uses electrical energy.

Definition

Electric power is the rate at which electrical energy is used in a circuit. In other words, it is the electrical energy used every second.

In topic 7, the energy supplied in a time t was VIt. Dividing by the time gives the energy used each second:

P=VItt=VI

Using Ohm’s law, the same power can be written in two more ways:

P=I2RP=V2R

Formula

P = VI

where

  • Pelectric powerwatt (W)
  • Vpotential differencevolt (V)
  • Icurrentampere (A)

The SI unit of power is the watt (W). An appliance uses 1 W when a current of 1 A flows through it at a potential difference of 1 V:

1 W=1 V × 1 A=1 J1 s

A larger unit is the kilowatt (kW): 1 kW = 1000 W.

Power rating

Every appliance carries a label like the one in Figure 10. “220 V, 880 W” means that the appliance uses 880 J of electrical energy every second when it is joined to a 220 V supply. From these two numbers, you can find the current it draws and its resistance.

An appliance rating label. Electric kettle. Rated voltage 220 V. Frequency 50 Hz. Rated power 880 W. Electric kettle Rated voltage220 V Frequency50 Hz Rated power880 W
Figure 10. A rating label of the kind found on appliances.

Worked example 14

An electric kettle is rated 220 V, 880 W. Find (a) the current it draws, and (b) its resistance when it is working. (c) Which fuse should be used with it: 3 A, 5 A or 15 A?

Given
P = 880 WV = 220 V
Find
Current I, resistance R, and a suitable fuse

Solution

I=PV=880 W220 V=4 AR=VI=220 V4 A=55 Ω

(a) 4 A (b) 55 Ω (c) The 5 A fuse. A 3 A fuse would melt in normal use, and a 15 A fuse would not melt until the current became dangerously large.

Energy and the kilowatt hour

The energy an appliance uses depends on its power and on how long it is used:

Formula

E = Pt

where

  • Eelectrical energy usedJ or kWh
  • PpowerW or kW
  • ttimes or h

The joule is far too small a unit for the energy used at home, so we use the kilowatt hour (kWh), the commercial unit of electrical energy. One kilowatt hour is the energy used by a 1 kW appliance in 1 hour. On an electricity bill, 1 kWh is called 1 unit.

1 kWh=1000 W × 3600 s=3 600 000 J=3.6 × 106 J

Electrons are not used up in a circuit. They keep flowing round it. What we pay for is the energy used to keep them moving through our appliances.

Worked example 15

A 1.5 kW water heater is used for 2 hours every day. How many units of electricity does it use in 30 days? What is the cost at ₹7 per unit?

Given
P = 1.5 kWtime = 2 h a day for 30 dayscost of 1 unit = ₹7
Find
Units used, and their cost

Solution

t=2 h × 30=60 hE=Pt=1.5 kW × 60 h=90 kWhCost=90 × ₹7=₹630

The heater uses 90 units of electricity, which cost ₹630.

Worked example 16

Two bulbs are rated 220 V, 100 W and 220 V, 40 W. Find the resistance of each. Which bulb has the higher resistance?

Given
Bulb 1: P1 = 100 WBulb 2: P2 = 40 WV = 220 V for both
Find
Resistances R1 and R2

Solution

R=V2PR1=(220 V)2100 W=48 400100 Ω=484 ΩR2=(220 V)240 W=48 40040 Ω=1210 Ω

The 40 W bulb has the higher resistance: 1210 Ω, compared with 484 Ω. At the same voltage, a larger resistance lets less current flow, so the power is smaller.

Remember

  • Power is the energy used each second: P = VI, which can also be written as I2R or V2R. Its unit is the watt (W).
  • The kilowatt hour is the commercial unit of electrical energy: 1 kWh = 3.6 × 106 J. On an electricity bill, 1 kWh is called 1 unit.
  • A rating such as “220 V, 880 W” gives the power used when the appliance is joined to a 220 V supply.
  • Choose a fuse rated a little above the normal current of the appliance.
Quick checkA 2 kW room heater is used for 3 hours. How many units of electricity does it use? How many joules is this?Show answer
E=2 kW × 3 h=6 kWh=6 × 3.6 × 106 J=2.16 × 107 J

It uses 6 units of electricity, which is 2.16 × 107 J.

Test yourselfTake the 22-question practice quiz on this chapter. Revising for the board exam?Get the Chapter 11 revision PDF: quick notes, 20 new board-pattern questions and full answers, for ₹49.