Chapter 7 · Physics

Work, Energy, and Simple Machines

Work, energy and power, and how simple machines help us: work done by a constant force, positive, negative and zero work, the work-energy theorem, kinetic and potential energy, conservation of mechanical energy, power, and the pulley, inclined plane and lever with their mechanical advantage.

Complete answers to every question in this chapter of the NCERT textbook: the questions in Activities 7.1 to 7.5, Think It Over and the questions in the text, the thirteen Pause and Ponder questions, all fifteen Revise, Reflect, Refine exercises and The Journey Beyond. Each question is given exactly as it appears in the book.

Activities 7.1 to 7.5

Questions in the activities

  1. Q1
    Activity 7.1: Let us investigate
    Raise the ball over the sand bed to a height of about 1 m and drop it (Fig. 7.17). Is a depression created in the sand? Why does the ball create a depression?

    Answer

    Yes. The raised ball has (gravitational potential) energy. As it falls, this becomes kinetic energy. On hitting the sand, the ball pushes the sand grains aside and down: it does work on the sand, which makes the depression.

  2. Q2
    Now, raise the ball to the height of 2 m and release it at a slightly different position over the sand bed such that the depressions do not overlap. Repeat this step one more time. Compare the depths of the depressions. Is there any difference? In which case is the depression deepest and in which case the shallowest?

    Answer

    Yes, the depths differ. The depression is deepest when the ball is dropped from the greatest height (2 m) and shallowest from the smallest height (1 m). More work was done to lift the ball higher, so it had more energy to do work on the sand.

  3. Q3
    Activity 7.2: Let us experiment
    Take the bob to one side to a point P, which is at the level of the horizontal line and let it go. Observe it at the extreme points of the first couple of oscillations. Does the bob almost reach the level of the horizontal line?

    Answer

    A simple pendulum. The bob is released from P, at height h above its lowest point Q. At P and at R, on the other side, it stops for a moment and has only potential energy. At Q it moves fastest and has only kinetic energy. It rises almost to the level of P again.PRQhOnly potentialenergyOnly potentialenergyOnly kinetic energy
    The bob rises almost to the level from which it was released.

    Yes, it rises almost to the line on the other side (point R) and again on the way back. Its potential energy at P turns into kinetic energy at Q and back into potential energy at R, so its mechanical energy stays nearly constant. It falls very slightly short each time because friction at the support and air resistance turn a little energy into heat.

  4. Q4
    Activity 7.3: Let us experiment
    Next, place the plank against the top of the pile of books or stool as shown in Fig. 7.27a. Pull the cart along the plank slowly and steadily. Is the reading of the spring balance (the force required) smaller than that of step 2?

    Answer

    Yes. Pulling the cart up the plank needs a smaller force than lifting it straight up (which needs a force equal to its weight). The plank is an inclined plane with a mechanical advantage greater than 1. But the cart has to be pulled over a longer distance.

  5. Q5
    Now, reduce the angle between the plank and the base as shown in Fig. 7.27b, and repeat the step 3. Observe how the force required changes as the plank becomes less steep.

    Answer

    An inclined plane of length L rising through a height h. A box of weight mg, the load, is pushed up the slope by an effort F prime. Ignoring friction, the effort times L equals mg times h, so the mechanical advantage is L divided by h.Effort F'Load mghL = length of the slope
    A longer, less steep plank needs a smaller effort.

    The force needed becomes smaller as the plank becomes less steep (and longer). Its mechanical advantage, Lh, increases because the length L grows while the height h stays the same.

  6. Q6
    Activity 7.4: Let us investigate
    On the other end of the scale, place one eraser. Does the stapler lift up? If not, add one more eraser.

    Answer

    With the pencil (fulcrum) close to the stapler, one or two light erasers at the far end lift the stapler. The erasers are much further from the fulcrum than the stapler is, so the small effort with a long effort arm balances the large load with a short load arm. The scale works as a lever.

  7. Q7
    Activity 7.5: Let us experiment
    Record all observations and measurements, and complete the Table 7.1 by adding more rows.

    Answer

    Sample readings, with the left pan (1 coin) kept 20 cm from the fulcrum:

    Coins in left pan, n1 (effort)Distance of left pan, L1 (cm)Coins in right pan, n2 (load)Distance of right pan, L2 (cm)
    120120
    120210
    12045
    12082.5

    In every row n1 × L1 = n2 × L2 (here 20): effort × effort arm = load × load arm. Doubling the load halves the distance at which it balances.

Think It Over and the questions in the text

In-text questions

  1. Q1
    Think It Over
    What will be the magnitude of velocity of the child at the bottom of the blue slide?

    Answer

    Ignoring friction, the child’s potential energy at the top, mgh, becomes kinetic energy at the bottom:

    12mv2=mghv=√(2gh)

    where h is the height of the top of the blue slide above its bottom. For example, a 3 m high slide gives v = √(2 × 9.8 × 3) ≈ 7.7 m s−1. In practice friction makes it a little less.

  2. Q2
    Think It Over
    Will two children of different masses reach the bottom of the same slide with the same velocity?

    Answer

    Yes (ignoring friction and air resistance). The mass cancels out of 12mv2 = mgh, so v = √(2gh) depends only on the height. The heavier child has more kinetic energy, but the same speed.

  3. Q3
    Think It Over
    Which of the slides will result in the largest magnitude of velocity for the child at its bottom?

    Answer

    Ignoring friction, the speed at the bottom depends only on the drop in height, not on the shape or length of the slide. So the slide with the greatest height from top to bottom gives the largest speed; slides of equal height give equal speeds. In real life, friction acts all along the slide, so a long winding slide (such as the spiral one) loses more energy, and the short, straight slide of the same height gives the largest speed.

  4. Q4
    What if …
    it were possible to build a perpetual motion machine, which once started, could continue doing useful work forever, without any fuel or electricity?

    Answer

    It would give unlimited free energy, with no fuel, no electricity bills and no pollution. But it is impossible. A machine cannot create energy: the work it does must come from energy supplied to it. And in every real machine, friction and air resistance turn some energy into heat, so with no input it gradually slows down and stops.

Pause and Ponder 1 to 13

Pause and Ponder

  1. Q1
    In the previous chapter, a weightlifter is shown holding a barbell steady in her hands (Fig. 6.8). Is she doing any work on the barbell while holding it steady?

    Answer

    No. The barbell does not move, so its displacement is zero, and W = F × 0 = 0. (She feels tired because her muscles use energy to keep pushing, but no work is done on the barbell.)

  2. Q2
    Is the work done by friction on the stack of coins that travels on a rough surface (Fig. 6.13c) — positive, negative or zero?

    Answer

    Negative. Friction acts opposite to the direction in which the stack moves, so the work it does is negative. This is why the stack slows down and stops: friction takes away its kinetic energy.

  3. Q3
    When you pedal a bicycle on a flat road, your muscles supply energy. In what forms does this muscular energy appear as you ride?

    Answer

    • Kinetic energy of you and the bicycle.
    • Heat (thermal energy): friction in the chain, pedals and wheel bearings, between tyres and road, and air resistance warm things slightly; your body also warms up.
    • A little sound from the chain and tyres.
  4. Q4
    Two objects A and B of mass m and 4 m have the same kinetic energy. What is the ratio of the magnitude of velocities of A and B?

    Answer

    12mvA2=12(4m)vB2vA2=4vB2vA=2vB

    The ratio of their speeds is 2 : 1: the lighter object moves twice as fast.

  5. Q5
    Does the kinetic energy of an object which moves with constant velocity change with its position?

    Answer

    No. Kinetic energy, 12mv2, depends only on mass and speed. At constant velocity the speed does not change, so the kinetic energy is the same at every position.

  6. Q6
    Does the potential energy of an object near the surface of the Earth change if it moves with constant velocity in the horizontal direction? What if the object is gradually raised in the vertical direction?

    Answer

    • Moving horizontally: no change. Its height stays the same, so U = mgh stays the same.
    • Raised vertically: its potential energy increases, by mg for every metre it rises.
  7. Q7
    For the situation depicted in Fig. 7.19, calculate the mechanical energy of the ball just before it hits the ground and show that even at this position, it is mgh.

    Answer

    Just before it hits the ground, its height is 0, so its potential energy is 0. It has fallen the full height h from rest:

    v2=u2 + 2gh=2ghK=12mv2=12m(2gh)=mgh

    Mechanical energy = 0 + mgh = mgh.

    So the mechanical energy is still mgh, the same as at the start.

  8. Q8
    You may have seen an exhibit like that in Fig. 7.22 in a science park, where a ball is released from the highest point. Describe how the kinetic energy and potential energy change at points A, B and C. Why do subsequent points, such as C, D and E, usually have lower heights compared to the previous ones? Could it have anything to do with the energy lost due to friction?

    Answer

    • From the high starting point down to A and on to the low point B, potential energy turns into kinetic energy: at B the ball is fastest (most kinetic, least potential energy).
    • Climbing from B towards C, kinetic energy turns back into potential energy; at the top of C the ball moves slowly (more potential, less kinetic energy). At A, a hump, it has more potential and less kinetic energy than at B.
    • Yes, friction is the reason the later humps are lower. Friction with the track and air resistance turn a little mechanical energy into heat all the time, so the ball has less mechanical energy for each later climb. If a hump were as high as the start, the ball could not get over it.
  9. Q9
    Explain why roads on hills are built to wind around in gentle slopes rather than going straight up (Fig. 4.26)?

    Answer

    A winding road is a long inclined plane of gentle slope. For the same height h, a longer road length L gives a larger mechanical advantage (Lh), so vehicles need a much smaller force to climb. Engines can manage it, the wheels do not slip, and braking downhill is safer. A road going straight up would be too steep to climb.

  10. Q10
    To reach a higher floor, we find climbing an inclined ladder easier in comparison to climbing a vertical ladder (Fig. 7.30). Explain why.

    Answer

    An inclined ladder works like an inclined plane: you rise the same height over a longer path, so each step needs a smaller upward push from your legs. Part of your weight is also supported by the sloping ladder, so your arms need not hold you up. On a vertical ladder you must lift your whole weight straight up at every step. The total work (mgh) is the same, but the force needed is smaller.

  11. Q11
    Why is it easier to open the lid of a can by using a spoon as shown in Fig. 7.35?

    Answer

    The spoon acts as a lever. Its tip rests on the rim of the can (the fulcrum) and is pushed under the lid (the load), very close to the fulcrum. Your hand pushes the far end of the handle, a long way from the fulcrum. A long effort arm and a short load arm give a large mechanical advantage, so a small push gives a large force that lifts the lid.

  12. Q12
    Why do you push an object closer to scissors fulcrum when you want to cut an object which is hard?

    Answer

    Scissors are a lever with the fulcrum at the screw. Moving the hard object closer to the screw makes the load arm shorter, while the effort arm (to your fingers) stays the same. Since effort × effort arm = load × load arm, the blades then press on the object with a larger force for the same effort.

  13. Q13
    Throughout history, many designs of perpetual machines (using wheels, weights or magnets) have been proposed but none actually work. Why do all real machines eventually slow down and stop? Explain in terms of work and energy.

    Answer

    A machine cannot make energy; it can only pass on the energy given to it. In every real machine, friction at the moving parts and air resistance do negative work, turning some mechanical energy into heat (and sound) all the time. With no fuel or other energy supplied, the machine’s energy keeps falling, so it slows down and stops. Wheels, weights and magnets only store and pass on energy; they cannot replace what friction takes.

Revise, Reflect, Refine 1 to 15

Exercises

  1. Q1
    State whether True or False.(i) Work is said to be done when a force is applied, even if the object does not move.(ii) Lifting a bucket vertically upward results in positive work done on the bucket.(iii) The SI unit for both work and energy is joule (J).(iv) A motionless stretched rubber band has kinetic energy.(v) Energy can change from one form to another.

    Answer

    • (i) False. Work needs a displacement in the direction of the force.
    • (ii) True. The lifting force and the displacement are both upwards.
    • (iii) True.
    • (iv) False. It is not moving, so it has no kinetic energy; it has (elastic) potential energy.
    • (v) True.
  2. Q2
    Fill in the blanks.(i) Work done = ______ × ______ (in the direction of force).(ii) 1 joule of work is done when a force of ______ newton displaces an object by 1 metre in the direction of the force.(iii) The expression for kinetic energy of a body of mass m and velocity v is ______.(iv) The potential energy of an object of mass m at a small height h from the Earth’s surface is ______.(v) Power is defined as the ______ at which work is done.

    Answer

    • (i) force × displacement
    • (ii) 1
    • (iii) 12mv2
    • (iv) mgh
    • (v) rate
  3. Q3
    When a ball thrown upwards reaches its highest point, tick which of the following statement(s) are correct?(i) The force acting on the ball is zero.(ii) The acceleration of the ball is zero.(iii) Its kinetic energy is zero.(iv) Its potential energy is maximum.

    Answer

    (iii) and (iv)

    • (i) is wrong: gravity (its weight) still acts on it.
    • (ii) is wrong: its acceleration is g, downwards.
    • (iii) is right: it stops for an instant, so K = 0.
    • (iv) is right: it is at its greatest height, so mgh is largest.
  4. Q4
    For each of the following situations, identify the energy transformation that takes place: (i) a truck moving uphill, (ii) unwinding of a watch spring, (iii) photosynthesis in green leaves, (iv) water flowing from a dam, (v) burning of a matchstick, (vi) explosion of a fire cracker, (vii) speaking into a microphone, (viii) a glowing electric bulb, and (ix) a solar panel.

    Answer

    SituationEnergy transformation
    (i) Truck moving uphillChemical (fuel) → kinetic and gravitational potential (some heat and sound)
    (ii) Unwinding watch springElastic potential → kinetic (of the gears and hands)
    (iii) PhotosynthesisLight → chemical
    (iv) Water flowing from a damGravitational potential → kinetic (→ electrical in the turbines)
    (v) Burning matchstickChemical → heat and light
    (vi) Exploding fire crackerChemical → heat, light, sound and kinetic
    (vii) Speaking into a microphoneSound → electrical
    (viii) Glowing bulbElectrical → light and heat
    (ix) Solar panelLight → electrical
  5. Q5
    A student is slowly lifted straight up in an elevator from the ground level to the top floor of a building. Later, the same student climbs the staircase, all the way to the top. Given that the height of the building is h = 72.5 m, acceleration due to gravity is g = 10 m s–2, and student’s mass is m = 50 kg.(i) Find the gain in the potential energy if the student is lifted straight up to the top.(ii) Find the gain in the potential energy when the student climbs the stairs to the same top.(iii) What do you conclude about the dependence of the potential energy on the path taken?

    Answer

    (i) U=mgh=50 kg × 10 m s−2 × 72.5 m=36 250 J

    (ii) The same: 36 250 J, since the student ends at the same height.

    (iii) The gain in potential energy depends only on the change in height, not on the path taken.

  6. Q6
    A crane lifts a mass m to the 10th floor of a building in a certain time. It then raises the same mass to the 20th floor of the same building in double the time. How much more energy and power are required? Assume that the height of all floors is equal.

    Answer

    Let each floor be h high and the first lift take time t.

    Energy for the 10th floor, E1, and for the 20th floor, E2:

    E1=mg × 10hE2=mg × 20h=2E1

    Power for the 10th floor:

    P1=10mght

    Power for the 20th floor:

    P2=20mgh2t=10mght

    Raising the mass from the ground to the 20th floor needs twice the energy (an extra 10mgh), but, since it takes twice as long, the same power: no extra power is needed.

    (If instead the crane lifted the mass on from the 10th floor to the 20th floor in double the time, it would need the same energy as the first lift but only half the power.)

  7. Q7
    Which factors determine the energy required to raise a flag from the ground to the top of a tall flagpole using a pulley? Does raising the flag slowly or quickly change the amount of work done? If the speed at which the flag is raised is doubled, how does the power requirement change? Explain your answers.

    Answer

    • The energy needed is mgh: it depends on the mass of the flag (and rope pulled up with it), the height of the pole and g. In practice, friction in the pulley adds a little more.
    • Raising it slowly or quickly does not change the work done: the flag gains the same potential energy either way (ignoring friction and the small kinetic energy).
    • Doubling the speed halves the time, so the power Wt is doubled.
  8. Q8
    A man of mass 60 kg rides a scooter of mass 100 kg. He accelerates the scooter to a velocity v. The next day, his son with a mass of 40 kg joins him as a passenger. If the scooter reaches the same speed on both days in the same time interval, what is the ratio of the fuel of the tank used on the two days? Assume that the energy transfer to the scooter happens entirely due to fuel, and no other losses occur due to air resistance and friction.

    Answer

    The fuel used is proportional to the kinetic energy given, 12mv2, and v is the same on both days.

    day 1 mass=60 kg + 100 kg = 160 kgday 2 mass=160 kg + 40 kg = 200 kgfuel ratio=12 × 160 × v212 × 200 × v2 = 160200=45

    The fuel used on the two days is in the ratio 4 : 5.

  9. Q9
    On a seesaw with sliding seats, a child is sitting on one side and an adult on the other side. The adult weighs twice that of the child. The seesaw however is balanced. Draw a figure which depicts this situation showing the distances from the fulcrum where the child and the adult are seated.

    Answer

    A balanced seesaw. The adult, of weight 2W, sits at distance d from the fulcrum; the child, of weight W, sits twice as far, at 2d.ChildAdultW2W2ddW × 2d = 2W × d
    The child sits twice as far from the fulcrum as the adult.

    For balance, weight × distance must be equal on both sides: W × 2d = 2W × d. So the child sits at twice the distance of the adult from the fulcrum (for example, child 2 m, adult 1 m).

  10. Q10
    A ball of mass 2 kg is thrown up with a velocity of 20 m s–1.(i) Identify the sign of the work done by gravity on the ball during its upward motion and its downward motion.(ii) If the ball reaches a height of 19.4 m, how much work was done by air resistance (assume g = 10 m s–2).

    Answer

    (i) Going up, gravity (downwards) acts opposite to the motion: negative work. Coming down, gravity acts along the motion: positive work.

    (ii) initial K=12 × 2 kg × (20 m s−1)2=400 JU at top=2 kg × 10 m s−2 × 19.4 m=388 Jwork by air=388 J − 400 J=−12 J

    Air resistance did −12 J of work: it took 12 J of energy from the ball, which is why it reached 19.4 m and not 20 m.

  11. Q11
    A 10.0 kg block is moving on horizontal floor with negligible friction. As shown in the Fig. 7.37, a variable force is applied on the block in its direction of motion from its position at 0 m till 4 m. If the block had a kinetic energy of 180 J when it was at 0 m, find the block’s speed (i) at 0 m, and (ii) at 4 m. Does the block have negative acceleration in any portion of its motion?

    Answer

    The graph rises from 0 N at 0 m to 50 N at 1 m, stays at 50 N up to 3 m, and falls to 0 N at 4 m.

    (i) v0=√(2Km)=√(2 × 180 J10 kg)=6 m s−1
    work done=(½ × 1 × 50) + (2 × 50) + (½ × 1 × 50) J=150 JK at 4 m=180 J + 150 J=330 J(ii) v=√(2 × 330 J10 kg)=√66 m s−1≈8.1 m s−1

    No. The force is never against the motion (it is positive or zero throughout), so the block only speeds up or keeps its speed; its acceleration is never negative.

  12. Q12
    The gravitational attraction on the surface of the Moon (lunar surface) is about 1/6th of that on the surface of the Earth. An astronaut can throw a ball up to a height of 8 m from the surface of the Earth. How far up will the ball thrown with the same upward velocity travel from the surface of the Moon?

    Answer

    At the top, all the kinetic energy has become potential energy: 12mu2 = mgh, so h = u22g. With the same u, the height is inversely proportional to g:

    hMoon=hEarth × gEarthgMoon=8 m × 6=48 m
  13. Q13
    A 1000 kg car is moving along a road at a constant speed. Suddenly, the driver notices some obstruction ahead and applies the brakes to come to a complete stop. The graphical representation of motion of the car starting from the instant the driver spots the traffic ahead is shown in Fig. 7.38.(i) Describe how the car moves between positions A and B.(ii) Calculate the kinetic energy of the car at A.(iii) State the work done by the brakes in bringing the car to a halt between B and C.(iv) What does the kinetic energy of the car transform into?

    Answer

    (i) From A (0 s) to B (1 s) the speed stays at 35 m s−1: the car moves at a constant speed while the driver reacts. The brakes act only from B; then the speed falls steadily to zero at C (3 s).

    (ii) K=12 × 1000 kg × (35 m s−1)2=612 500 J

    (iii) The brakes remove all this kinetic energy, so they do −612 500 J of work (negative, as their force opposes the motion).

    (iv) Mostly into heat (thermal energy) in the brakes and tyres, with a little sound.

  14. Q14
    The potential energy-displacement graph of a 0.5 kg ball moving along a frictionless track is shown in Fig. 7.39. At O, the velocity of the ball is 0 m s–1 and potential energy is 30 J. Calculate the velocity of the ball at P, Q and R.

    Answer

    With no friction, the mechanical energy stays at its value at O: 30 J (potential) + 0 (kinetic) = 30 J. From the graph, the potential energy is about 20 J at P, 30 J at Q and 40 J at R.

    at P: K=30 J − 20 J = 10 Jv=√(2 × 10 J0.5 kg)=√40 m s−1 = 2√10 m s−1 ≈ 6.3 m s−1

    At Q: potential energy 30 J, so the kinetic energy is 0 and the ball is momentarily at rest (v = 0); it turns back there.

    At R: the potential energy (40 J) would be more than the total energy (30 J), which is impossible. The ball can never reach R; it turns back at Q.

  15. Q15
    A coconut of mass 1.5 kg falls from the top of a coconut tree onto the wet sand on a beach. The height of the tree is 10 m. On impact, the coconut comes to rest by making a depression in the sand.(i) Calculate the velocity of the coconut just before it hits the sand.(ii) Assume that the average resistive force of sand is 3000 N and all of the coconut’s energy is used to create the depression in the sand. Calculate the depth of the depression the coconut makes in the sand. Assume g = 10 m s–2.

    Answer

    (i) v=√(2gh)=√(2 × 10 × 10) m s−1=√200 m s−1 = 10√2 m s−1 ≈ 14.1 m s−1
    (ii) energy=mgh = 1.5 × 10 × 10 J=150 Jdepth=150 J3000 N=0.05 m = 5 cm

    The coconut makes a depression about 5 cm deep.

The Journey Beyond

The Journey Beyond

  1. Q1
    Remove both the ends from a pen so that the refill can slide freely through the barrel (Fig. 7.40). … Stretch and release the rubber band. The refill shoots out, showing the conversion of elastic potential energy into kinetic energy. Repeat with different amounts of stretch, and observe how the distance travelled changes. Is there a relationship between the stretch and the distance travelled?

    Answer

    Yes. The more the band is stretched, the further the refill travels. The energy stored grows faster than the stretch itself (doubling the stretch stores roughly four times the energy), so the distance increases sharply with stretch, until the band is near its limit. Record stretch and distance in a table, plot a graph, and repeat each reading three times for a fair test.

  2. Q2
    Construct one or more simple machines, or a combination of them (lever, pulley, and inclined plane) using easily available materials … Use your model to lift or move a small load, measure the effort and the load, and calculate the mechanical advantage.

    Answer

    • Lever: a ruler on a pencil (fulcrum), with paper cups at the ends; place coins as the load near the fulcrum and add coins as the effort until it balances.
    • Pulley: two bottle caps glued face to face on a pencil axle, hung from a support; a thread over it lifts a cup of coins.
    • Inclined plane: a cardboard or wooden plank on a pile of books; pull a toy car up it with a rubber band or spring balance.

    Weigh the load and measure the effort (with a spring balance, or by counting coins). Then mechanical advantage = loadeffort. Expect about 1 for a single fixed pulley, about Lh for the ramp (a little less because of friction), and effort armload arm for the lever.

  3. Q3
    Computer simulations can help in visualising physical quantities that are difficult to observe directly. The PhET simulations (https://phet.colorado.edu) provide interactive models, such as Energy Skate Park, Energy Forms and Changes, Pendulum Lab, and Masses and Springs. Use these to explore how different forms of energy change as parameters, such as mass, height, and friction are varied.

    Answer

    • Energy Skate Park: with friction off, the skater always returns to the same height and the total energy bar stays fixed; with friction on, thermal energy grows and the skater rises less each time. Changing the mass changes the energies but not the speeds.
    • Pendulum Lab: longer strings swing more slowly; the energy bars swap between potential and kinetic each swing.
    • Masses and Springs: a heavier mass stretches the spring more; watch elastic, gravitational and kinetic energy exchange as it bounces.