Chapter 10 · Physics

Sound Waves: Characteristics and Applications

How sound is made, travels and is used: vibrations, propagation through a medium, compressions and rarefactions, longitudinal waves, the energy of sound, the density graph, wavelength, frequency, time period, amplitude, intensity, the speed of sound, pitch, loudness and the audible range, echo and reverberation, and uses of ultrasound and infrasound.

Complete answers to every question in this chapter of the NCERT textbook: the questions in Activities 10.1 to 10.8, Think It Over and the questions in the text, all thirteen Pause and Ponder questions, all fifteen Revise, Reflect, Refine exercises and The Journey Beyond. Each question is given as it appears in the book.

Activities 10.1 to 10.8

Questions in the activities

  1. Q1
    Activity 10.1: Let us explore
    Holding the box steady with one hand, pluck the rubber band with a finger. Do you hear any sound? … Is it vibrating? … Wait till the rubber band stops vibrating. Do you still hear the sound?

    Answer

    • Yes, a twanging sound is heard.
    • Yes, the band is seen moving rapidly to and fro; it looks blurred.
    • No. The sound stops when the vibration stops. Sound is produced by vibration.
  2. Q2
    Change the tension in the rubber band by stretching it more or loosening it slightly and plucking it each time. Does the sound change? What changes do you notice?

    Answer

    Yes. When the band is stretched more, it vibrates faster and the sound becomes higher-pitched (shriller). When it is loosened, it vibrates more slowly and the sound becomes lower (deeper).

  3. Q3
    Remove the rubber band from the box. Stretch it between two fingers and pluck it near your ear. Is the sound still produced? Is it as loud as before?

    Answer

    Yes, a sound is still produced, but it is much fainter. On the box, the vibrating band also sets the box and the air inside it vibrating, which makes the sound louder.

  4. Q4
    Activity 10.2: Let us explore
    Strike one of the prongs of the tuning fork gently against the rubber pad and bring it close to your ear. Do you hear a sound? … gently touch a water surface with one of the vibrating prongs … Do you see waves forming on the surface of water? … bringing the prongs of the tuning fork near your ear in different orientations. Do you hear the sound?

    Answer

    • Yes, a steady humming sound.
    • Yes, small waves (ripples) spread out and water may splash, showing that the prongs are vibrating.
    • Yes, in every orientation, which shows that sound spreads out from the fork in many directions.
  5. Q5
    Activity 10.3: Let us investigate
    Now, place your ear against the desk, close your other ear and listen again … Are you able to hear the sound through the table?

    Answer

    Yes, and the knock or scratch sounds even louder and clearer than through the air. Sound travels through solids.

  6. Q6
    Activity 10.4: Let us investigate
    Now, submerge the two metal spoons in water … and tap them against one another again. Do you again hear the sound produced? … If sound did not travel through liquids, would you have heard this sound?

    Answer

    Yes, the tapping is heard. No, if sound could not travel through liquids we would not hear it, because the sound has to pass through the water before it reaches the air and our ears.

  7. Q7
    Activity 10.5: Let us observe
    Give the slinky at your end a sharp push towards your friend and then quickly pull it back again. Do you observe a disturbance created in the slinky which moves towards your friend? … Are a series of disturbances produced in the slinky? Do these disturbances move across the length of slinky? Does the mark on the slinky move back and forth parallel to the direction of the disturbance?

    Answer

    • Yes, a region of bunched-up turns travels along the slinky to the friend.
    • Yes, repeated pushes and pulls make a series of bunched-up regions (compressions) and spread-out regions (rarefactions).
    • Yes, they travel along the whole length.
    • Yes, the mark only moves back and forth about its place, parallel to the direction of the disturbance. It does not travel along the slinky.
  8. Q8
    Activity 10.6: Let us experiment
    Produce a loud sound near the bowl without touching it. Observe the grains on the sheet. Does the sound have any effect on the grains? … Why does this happen, even though the source of sound is not touching the sheet or the container?

    Answer

    Yes, the grains jump and move about; they jump higher for louder sounds. The sound wave travels through the air, reaches the sheet and makes it vibrate, and the vibrating sheet throws the grains up. So sound carries energy.

  9. Q9
    Activity 10.7
    Compare the musical notes by taking the ratio of each frequency with respect to the ‘Sa’. Do you observe any pattern?

    Answer

    The frequency rises from one note to the next, and each note has a fixed ratio to Sa, whatever the starting Sa. The upper Sa has exactly twice the frequency of the lower Sa (an octave). With Sa at 240 Hz, typical values are:

    NoteSaReGaMaPaDhaNiSa (upper)
    Frequency (Hz)240270300320360400450480
    Ratio to Sa198544332531582

    Your measured values will be close to these. A phone and a voice give nearly the same frequency for the same note.

  10. Q10
    Activity 10.8
    Increase the frequency in steps of 100 Hz up to 1000 Hz and describe how the sound changes. … set the frequency to 50 Hz. Reduce the frequency till about 20 Hz or the point where you cannot hear the sound anymore.

    Answer

    As the frequency goes up from 100 Hz to 1000 Hz, the sound becomes steadily higher in pitch (shriller). Going down from 50 Hz, the sound becomes a deep hum and grows fainter, until near 20 Hz it can hardly be heard at all: this is the lower limit of human hearing.

Think It Over and the questions in the text

In-text questions

  1. Q1
    Think It Over
    Two astronauts are repairing the arm of a space station together during a spacewalk. Can they talk to each other and hear the sounds of metal clanking as they do on the Earth?

    Answer

    No. Space is nearly a vacuum, and sound needs a medium to travel. They talk using radio sets fitted in their spacesuits. (They may feel a clank as a vibration through the metal they are touching, because sound can travel through solids.)

  2. Q2
    Think It Over
    How do most bats use sound to locate their prey in the dark at night?

    Answer

    By echolocation. A bat sends out short bursts of ultrasound. The sound reflects off insects and obstacles, and from the echoes the bat works out where they are.

  3. Q3
    Which form of energy gets converted to sound energy? How is sound produced and how does it reach our ears?

    Answer

    Usually mechanical energy: the energy of a vibrating object, such as a plucked string, a struck drum or our vocal cords (a speaker turns electrical energy into sound). Sound is produced by vibrations, and it reaches our ears through a medium, usually air, as a wave of compressions and rarefactions.

  4. Q4
    Threads of Curiosity
    While talking or singing, gently touch your throat. Do you feel vibrations anywhere?

    Answer

    Yes, a buzzing vibration is felt at the front of the throat, over the voice box (larynx), where the vocal cords vibrate.

  5. Q5
    A space where there is no medium (matter) is referred to as vacuum. Would you hear sound in vacuum?

    Answer

    No. Sound needs a medium to travel; the vacuum bell jar experiment shows this.

  6. Q6
    What if …
    the speed of sound in air depended on its frequency? Would music still sound pleasant when a singer performs with instruments? Why or why not?

    Answer

    No. High and low notes played at the same moment would reach the listener at different times, and the gap would grow with distance. The voice and the instruments would be out of step, chords would break up, and the music would sound jumbled, especially at the back of a hall.

  7. Q7
    What if …
    humans could detect ultrasonic waves like dogs can? What would be the advantages and disadvantages?

    Answer

    • Advantages: we could hear bats and other animals that use ultrasound, notice faults in machines early, and perhaps sense obstacles by echoes in the dark.
    • Disadvantages: many devices give out ultrasound (parking sensors, cleaners, pest repellers, motion detectors), so we would hear constant extra noise that could be annoying, distracting and tiring.

Pause and Ponder 1 to 13

Pause and Ponder

  1. Q1
    Explore various ways of producing sound.

    Answer

    • Plucking a string (sitar, guitar, rubber band).
    • Striking or beating (drum, bell, tabla, taal).
    • Blowing air (bansuri, whistle, conch).
    • Bowing or rubbing (violin, sarangi, a wet finger round a glass).
    • Shaking (rattle, maracas, ghungroo).
    • Electrically, with a speaker or a buzzer.
  2. Q2
    Make a list of different types of musical instruments and identify their vibrating parts which produce sound.

    Answer

    TypeExamplesVibrating part
    StringSitar, veena, sarangi, guitar, violinStretched strings
    Membrane (percussion)Tabla, dholak, mridangam, drumStretched skin or membrane
    WindBansuri, shehnai, harmonium, trumpetAir column (with reeds in some)
    Solid (percussion)Ghatam, cymbals, jal tarang, xylophone, bellThe body of the instrument
  3. Q3
    Assertion (A): We cannot hear the sound of a bell ringing in a closed jar after most of the air is pumped out.
    Reason (R): Sound requires a medium to travel.
    Choose the correct statement:(i) Both A and R are true, but R is not the correct explanation of A.(ii) Both A and R are true, and R is the correct explanation of A.(iii) A is true, but R is false.(iv) A is false, but R is true.

    Answer

    (ii) Both A and R are true, and R is the correct explanation of A.

    With the air removed there is almost no medium, so the sound cannot reach us. R correctly explains A.

  4. Q4
    Assertion (A): Compressions and rarefactions move through the medium.
    Reason (R): Individual particles of the medium continuously move forward with the wave.
    Choose the correct statement:(i) Both A and R are true, but R is not the correct explanation of A.(ii) Both A and R are true, and R is the correct explanation of A.(iii) A is true, but R is false.(iv) A is false, but R is true.

    Answer

    (iii) A is true, but R is false.

    The particles only vibrate about their mean positions; they do not travel with the wave.

  5. Q5
    When sound travels from a tuning fork to your ear, which of the following actually reaches your ear?(i) Air particles near the tuning fork(ii) Energy carried by sound waves(iii) The tuning fork material(iv) A continuous stream of compressed air

    Answer

    (ii) Energy carried by sound waves

    A sound wave transfers energy, not the particles of the medium.

  6. Q6
    The variation of density of the medium for two sound waves is shown in Fig. 10.17 (a) and (b). Label compression and rarefaction by C and R on it. In the graph given in Fig. 10.17 (c) and (d), label the axes and draw the curves corresponding to Fig. 10.17 (a) and (b).

    Answer

    Mark C at the middle of each crowded band of particles and R at the middle of each sparse band. Label the y-axis “Density” and the x-axis “Distance”, and draw the dashed average-density line. The curve rises to a crest under each C and falls to a trough under each R:

    Two density patterns with compressions marked C and rarefactions marked R, each drawn above its graph of density against distance. The graph is above the average line at each C and below it at each R. The second pattern has a smaller change in density, so its curve has a smaller amplitude.(a) and (c)RCRCRDensityDistance(b) and (d)RCRCRDensityDistance
    How to answer: crests below the compressions, troughs below the rarefactions.

    Where the crowding is more marked, the curve rises and falls more (a larger amplitude). Match the positions of your C and R to the bands in your book’s figure.

  7. Q7
    Conduct Activity 10.1 once again with a thick rubber band and then with a thin rubber band. Does the thin rubber band vibrate faster than the thick rubber band? If yes, how do the frequency and time period of the sound produced by the thin rubber band differ from that of the thick rubber band?

    Answer

    Yes (at the same stretch). The thin band has a higher frequency and so a shorter time period; its sound is higher in pitch.

  8. Q8
    If the frequency of a sound wave produced by an oscillating piston of a long tube filled with air is 20 Hz, then how many oscillations does the piston complete per minute?

    Answer

    number=20 × 60=1200

    The piston completes 1200 oscillations per minute.

  9. Q9
    For the sound wave represented by the graph shown in Fig. 10.19, what is half of its wavelength?

    Answer

    The curve starts on the average line at 0, crosses it again at 1.5 cm and completes one full wave at 3.0 cm. So λ = 3.0 cm.

    λ2=3.0 cm2=1.5 cm
  10. Q10
    Table 10.1 shows the speed of sound in a few media at atmospheric pressure. … Compare the speeds in different media by finding the ratio of(i) the speed of sound in water with respect to the speed in the air.(ii) the speed of sound in steel with respect to the speed in the water.

    Answer

    (i) ratio=1500 m s−1340 m s−1=4.4 (about 75 : 17)
    (ii) ratio=5000 m s−11500 m s−1=3.3 (10 : 3)

    Sound is about 4.4 times faster in water than in air, and about 3.3 times faster in steel than in water.

  11. Q11
    Two friends are standing along a steel fence at a distance of 340 m from each other. Gunjan places her ear over the fence and her friend knocks the fence with a metal object. … calculate the time difference between the sound that reached Gunjan through the air and the steel. Would it have been possible for her to distinguish between the two sounds? (The time interval between two sounds must be at least 0.1 s to be heard separately.)

    Answer

    time in air=340 m340 m s−1=1 stime in steel=340 m5000 m s−1=0.068 sdifference=1 s − 0.068 s=0.932 s

    The difference, 0.932 s, is much more than 0.1 s, so yes: she hears two separate knocks, first through the steel and then through the air.

  12. Q12
    An experiment is being set up that requires echoes to arrive at least 0.2 s after the emission of sound. What minimum distance should a reflecting surface be placed at? Assume the speed of sound to be 343 m s–1.

    Answer

    d=v × t2=343 m s−1 × 0.2 s2=34.3 m

    The surface must be at least 34.3 m away.

  13. Q13
    Sound travels much farther in water than light, and thus, is used for various underwater applications. A sonar signal sent to find the depth of ocean takes 4 s to return. What is the depth of the ocean at that location if the speed of sound in seawater is 1500 m s–1?

    Answer

    depth=1500 m s−1 × 4 s2=3000 m

    The ocean is 3000 m (3 km) deep there.

Revise, Reflect, Refine 1 to 15

Exercises

  1. Q1
    Which observation best supports the idea that sound is a mechanical wave?(i) Sound shows reflection(ii) Sound needs a medium to propagate(iii) Sound has frequency(iv) Sound carries energy

    Answer

    (ii) Sound needs a medium to propagate

    A mechanical wave is one that needs a material medium. Light also reflects, has a frequency and carries energy, but needs no medium.

  2. Q2
    For a sound wave propagating in a medium, increasing its frequency will increase its(i) wavelength(ii) speed(iii) number of compressions per second(iv) time period

    Answer

    (iii) number of compressions per second

    The speed depends on the medium and stays the same; the wavelength and time period decrease.

  3. Q3
    If 20 compressions pass a point in 4 seconds, the frequency is(i) 80 Hz(ii) 5 Hz(iii) 10 Hz(iv) 0.2 Hz

    Answer

    (ii) 5 Hz

    ν=204 s=5 Hz
  4. Q4
    In a room, the reflected sound reaches the ear 0.05 s after its production. Will it produce an echo or reverberation? Justify your answer.

    Answer

    Reverberation. An echo is heard only if the reflected sound arrives at least 0.1 s after the original sound. At 0.05 s the reflection merges with the original sound, and repeated reflections from the walls make the sound persist: that is reverberation.

  5. Q5
    Graphs representing two sound waves are given in Fig. 10.30. If the scales on the X and Y axes of the two graphs are the same, which of the two sound waves has (i) greater wavelength, and (ii) smaller amplitude?

    Answer

    • (i) Wave (a): its crests are farther apart (fewer waves over the same distance).
    • (ii) Wave (a): its crests rise less above the average line.
  6. Q6
    The sound waves emitted by three sources A, B and C are represented in Fig. 10.31. If the frequency of A is maximum and C is minimum, identify the corresponding curves, and mark A, B and C on them.

    Answer

    All three travel in the same medium at the same speed, so the highest frequency has the shortest wavelength (most waves in the same distance).

    • A: the green curve, with the most waves (shortest wavelength).
    • B: the red curve.
    • C: the blue curve, with the fewest waves (longest wavelength).
    The three waves of Fig. 10.31 labelled. A, the green curve, has the most waves in the same distance, so the shortest wavelength and the highest frequency. B, the red curve, is in between. C, the blue curve, has the longest wavelength and the lowest frequency.DensityDistanceABC
    Fig. 10.31 with the curves marked.
  7. Q7
    Draw a graph to represent a sound wave for which the density amplitude is 3 units and wavelength is 4 cm.

    Answer

    Draw the average-density line. The curve rises 3 units above it and falls 3 units below it, and repeats every 4 cm: crests at 1 cm and 5 cm, troughs at 3 cm and 7 cm.

    A graph of density against distance in centimetres. The curve rises 3 units above the average line and falls 3 units below it, and repeats every 4 centimetres: crests at 1 and 5 centimetres, troughs at 3 and 7 centimetres.012345678DensityDistance (cm)λ = 4 cm3 unitsaverage
    Amplitude 3 units, wavelength 4 cm.
  8. Q8
    In a movie, while showing the explosion of a spacecraft in space, a flash of light is shown along with sound at the same time. What are the errors in this depiction?

    Answer

    • No sound should be heard at all. Space is nearly a vacuum, and sound cannot travel without a medium. Only the flash would be seen.
    • Even where there is a medium, the sound would arrive after the flash, because light travels far faster than sound. They would not reach the viewer together.
  9. Q9
    A source produces a sound wave of wavelength 3.44 m. If the wave travels with a speed of 344 m s–1 find its time period.

    Answer

    T=λv=3.44 m344 m s−1=0.01 s

    The time period is 0.01 s (frequency 100 Hz).

  10. Q10
    A ship searching for a sunken ship sent a sonar signal and detected an echo after 5 s. If ultrasonic wave travels at 1525 m s–1 in seawater, approximately how far down in the ocean is the wreckage of the sunken ship located?

    Answer

    depth=1525 m s−1 × 5 s2=3812.5 m

    The wreck is about 3810 m (3.8 km) down.

  11. Q11
    A vehicle is fitted with an ultrasonic distance sensor … When the warning beep starts sounding at a distance of 1.2 m from the obstacle, how much time is taken by ultrasonic wave to travel to the obstacle and come back? Assume the speed of ultrasonic wave in air to be 345 m s–1.

    Answer

    The wave travels 1.2 m to the obstacle and 1.2 m back: 2.4 m in all.

    t=2.4 m345 m s−1=0.00696 s≈7 ms

    It takes about 0.007 s (7 milliseconds).

  12. Q12
    The speed of sound in air is about 331 m s–1 at 0 ºC and nearly 344 m s–1 at 22 ºC. Roughly how much extra time will the sound of thunder take to travel a distance of 1720 m, if the air temperature changes from 22 ºC to 0 ºC? Assume that all other conditions remain unchanged.

    Answer

    time at 22 °C=1720 m344 m s−1=5.00 stime at 0 °C=1720 m331 m s−1=5.20 sextra time=1720331 s − 5 s=65331 s≈0.2 s

    The thunder takes roughly 0.2 s longer in the colder air.

  13. Q13
    The variation of density of medium for a sound wave propagating with a speed of 340 m s–1 is shown in Fig. 10.32. Calculate the wavelength and frequency of the sound wave.

    Answer

    The 8 cm marked in the figure runs from the middle of one compression to the middle of the compression after next: two wavelengths.

    λ=8 cm2=4 cm = 0.04 mν=vλ=340 m s−10.04 m=8500 Hz

    Wavelength 4 cm; frequency 8500 Hz (8.5 kHz).

  14. Q14
    The graphical representation of two sound waves A and B propagating at the same speed of 345 m s–1 is shown in Fig. 10.33. What is the wavelength of each of them? Also, calculate their frequencies.

    Answer

    Wave A completes one full wave between 0 and 2.5 cm; wave B completes one full wave between 0 and 5.0 cm.

    λA=2.5 cm = 0.025 mνA=345 m s−10.025 m=13 800 Hz
    λB=5.0 cm = 0.05 mνB=345 m s−10.05 m=6900 Hz

    A: 2.5 cm and 13 800 Hz. B: 5.0 cm and 6900 Hz. Half the wavelength means twice the frequency.

  15. Q15
    Two identical sound sources are placed at A and B — one in air and one submerged in water (Fig. 10.34). Both produce sounds at the same time, which travel horizontally to the vertical side of the cliff and come back. If the time taken by the sound to return to A is 4.5 times than that of B, what is the ratio between the speeds of sound in air and water?

    Answer

    Both sounds travel the same distance, 2d, to the cliff and back. For the same distance, speed is inversely proportional to time.

    vairvwater=tBtA=14.5=29

    The ratio of the speeds of sound in air and water is 2 : 9 (sound is 4.5 times faster in water).

The Journey Beyond

The Journey Beyond

  1. Q1
    Many people use earphones extensively these days. Find out the research studies that might have been done to understand the impact of excessive use of earphones on hearing (if any). Also, find out how hearing is tested and what are the decibel ranges for defining mild, moderate and severe hearing loss. What are the government schemes … Write an article on your findings.

    Answer

    • Studies by the World Health Organization (WHO) warn that over a billion young people risk hearing loss from loud music through earphones. A safe habit is the 60–60 rule: no more than 60% volume for no more than 60 minutes at a time.
    • Hearing is tested with an audiometer: tones of different frequencies are played at falling loudness, and the softest level heard is plotted on an audiogram.
    • WHO grades (the softest sound heard in the better ear): normal below 20 dB; mild 20 to 35 dB; moderate 35 to 50 dB; moderately severe 50 to 65 dB; severe 65 to 80 dB; profound 80 to 95 dB.
    • In India, the ADIP scheme (Assistance to Disabled Persons for Purchase or Fitting of Aids and Appliances) helps with hearing aids and provides cochlear implants for young children. Check the current rules on the government website.

    Use these points as the outline of your article, and add the sources you read.

  2. Q2
    Make a cone using a poster paper or cardboard and adhesive tape. Cover a mobile phone that is playing music with the cone. Compare the loudness of the sound with and without the cone. … Try experimenting with different shapes and record your observations.

    Answer

    The music sounds louder in front of the cone. The cone stops the sound spreading out in all directions and guides its energy forward, so the intensity in front is greater. A sound-level app shows a higher dB reading. A longer cone with a wide mouth usually works best; a cylinder helps less.

  3. Q3
    How does the curved design of ceilings and walls behind the stage in concert and conference halls improve the quality of sound for the audience compared to flat surfaces? …

    Answer

    Curved ceilings and curved walls behind the stage reflect the sound from the stage evenly towards the audience, rather than straight back or upwards. Every seat gets enough sound, and the reflections arrive quickly enough to strengthen the sound without making an echo. Flat surfaces can send sound in unhelpful directions and leave some seats quieter.

  4. Q4
    Carry out a simple activity to measure the speed of sound, along with a friend in a large open ground of size 200 m or more. … What value of speed did you get from the experiment? … Why did you measure the time between ‘seeing’ and ‘hearing’ the balloon burst?

    Answer

    For example, if the distance is 240 m and the average time is 0.70 s:

    speed=240 m0.70 s≈343 m s−1

    Results usually lie between about 300 and 380 m s−1, because reaction time is a large part of such short times. Averaging many trials, and a longer distance, makes the result better.

    Why seeing and hearing? Light covers the distance almost instantly, so seeing the burst marks the moment the sound starts. The time until it is heard is then the time the sound takes to travel the distance.

  5. Q5
    Explore the internet resources to explore the effect of humidity and temperature on the speed of sound. …

    Answer

    The simulations show that sound travels faster in warmer air (about 0.6 m s−1 faster for each 1 °C rise) and slightly faster in more humid air, because water vapour is lighter than the nitrogen and oxygen it replaces. A frequency change alters the wavelength but not the speed.