Chapter 4 · Science

Electricity: Magnetic and Heating Effects

How an electric current makes a magnetic field, how electromagnets are made and used, why wires get hot and how we use and control that heat, how cells and batteries make electricity, and the symbols used to draw circuits.

Answers to all 11 questions under “Keep the curiosity alive” at the end of the chapter. Each question is given exactly as it appears in the book. The page also has a box asking you to prepare some questions of your own, and a “Discover, design, and debate” list of projects. Those are for you to do, so they are not answered here.

Keep the curiosity alive

Questions 1 to 11

  1. Q1
    Fill in the blanks:(i) The solution used in a Voltaic cell is called ________.(ii) A current carrying coil behaves like a _______ .

    Answer

    (i) The solution used in a Voltaic cell is called electrolyte.

    (ii) A current carrying coil behaves like a magnet (an electromagnet).

  2. Q2
    Choose the correct option:(i) Dry cells are less portable compared to Voltaic cells. (True/False)(ii) A coil becomes an electromagnet only when electric current flows through it. (True/False)(iii) An electromagnet, using a single cell, attracts more iron paper clips than the same electromagnet with a battery of 2 cells. (True/False)

    Answer

    (i) False. Dry cells are more portable. Their electrolyte is a paste, so nothing spills, and they are small and light.

    (ii) True. The coil is a magnet only while current flows. When the current stops, the magnetic effect disappears.

    (iii) False. A battery of 2 cells gives a larger current. So the electromagnet is stronger and attracts more clips than with one cell.

  3. Q3
    An electric current flows through a nichrome wire for a short time.(i) The wire becomes warm.(ii) A magnetic compass placed below the wire is deflected.

    Choose the correct option:

    (a) Only (i) is correct(b) Only (ii) is correct(c) Both (i) and (ii) are correct(d) Both (i) and (ii) are not correct

    Answer

    (c) Both (i) and (ii) are correct

    A current always has both effects. Nichrome has high resistance, so the wire gets warm (heating effect). Any wire carrying a current also has a magnetic field round it, so the compass needle turns (magnetic effect).

  4. Q4
    Match the items in Column A with those in Column B.
    Column AColumn B
    (i) Voltaic cell(a) Best suited for electric heater
    (ii) Electric iron(b) Works on magnetic effect of electric current
    (iii) Nichrome wire(c) Works on heating effect of electric current
    (iv) Electro­magnet(d) Generates electricity by chemical reactions

    Answer

    Column AColumn B
    (i) Voltaic cell(d) Generates electricity by chemical reactions
    (ii) Electric iron(c) Works on heating effect of electric current
    (iii) Nichrome wire(a) Best suited for electric heater
    (iv) Electro­magnet(b) Works on magnetic effect of electric current
  5. Q5
    Nichrome wire is commonly used in electrical heating devices because it(i) is a good conductor of electricity.(ii) generates more heat for a given current.(iii) is cheaper than copper.(iv) is an insulator of electricity.

    Answer

    (ii) generates more heat for a given current.

    Nichrome has high resistance, so it turns more electrical energy into heat. It also has a high melting point and does not rust when red hot. It is not the best conductor (copper is better), and it is not an insulator: current does flow through it.

  6. Q6
    Electric heating devices (like an electric heater or a stove) are often considered more convenient than traditional heating methods (like burning firewood or charcoal). Give reason(s) to support this statement considering societal impact.

    Answer

    • Cleaner air at home: they give no smoke or soot. Smoke from wood and charcoal harms the lungs and eyes, especially of women and children who cook.
    • Saves trees: less firewood is cut, so forests are protected.
    • Saves time and effort: no one needs to collect wood or carry charcoal. That time can go to school or work.
    • Easy to control: they start at the press of a switch, and the heat can be set and turned off at once.
    • Safer and cleaner: there is no open flame, no ash and less risk of burns, if they are used with care.

    The electricity should come from clean sources, such as solar or wind power, to reduce pollution at the power station too.

  7. Q7
    Look at the Fig. 4.4a. If the compass placed near the coil deflects: (i) Draw an arrow on the diagram to show the path of the electric current. (ii) Explain why the compass needle moves when current flows. (iii) Predict what would happen to the deflection if you reverse the battery terminals.

    Fig. 4.4a shows a coil wound on an iron nail, with its ends marked A and B. The coil is joined to a cell (− on the left, + on the right). A compass is placed near end A. It is redrawn below.

    Fig. 4.4a redrawn: a coil wound on an iron nail, with ends marked A and B, joined to a cell. A compass placed near end A has its north end pointing towards A.+−NESWABcell: − on the left, + on the right
    Fig. 4.4a, redrawn.

    Answer

    (i) Current leaves the + terminal of the cell, goes up the wire to end B, round the coil to end A, and back down to the − terminal.

    The same coil with arrows showing the current: from the + end of the cell up to end B, along the coil to end A, and down to the − end of the cell.+−NESWABcurrentcell: − on the left, + on the right
    The path of the current.

    (ii) A coil carrying a current makes a magnetic field and acts like a magnet. The iron nail inside makes it stronger. The compass needle is a small magnet, so the field pushes and pulls its poles and it turns. Here its north end is pulled towards end A, so end A is a south pole.

    (iii) The current would flow the other way round the coil, so the poles would swap. End A would become a north pole. The compass needle would turn the opposite way: its north end would now be pushed away from A. The size of the deflection would stay about the same.

  8. Q8
    Suppose Sumana forgets to move the switch of her lifting electromagnet model to OFF position (in introduction story). After some time, the iron nail no longer picks up the iron paper clips, but the wire wrapped around the iron nail is still warm. Why did the lifting electromagnet stop lifting the clips? Give possible reasons.

    Answer

    • The battery ran down. With the switch left on, current flowed all the time and the chemicals in the cells were used up. The current became too small to make a strong magnet.
    • Energy was wasted as heat. Much of the battery’s energy turned into heat in the wire. That is why the coil is warm. The wire stays warm for a while even after the current has become very small.
    • A loose connection. The heat may have softened the tape or loosened a wire, so little or no current reaches the coil.

    An electromagnet works only while enough current flows. Fresh cells, or a battery that is switched off when not in use, would fix it.

  9. Q9
    In Fig. 4.12, in which case the LED will glow when the switch is closed?

    The book shows two beakers, each with an iron nail and a copper strip joined through an LED and a switch. Beaker (a) holds lemon juice and beaker (b) holds pure water. It is redrawn below.

    Fig. 4.12 redrawn. Two beakers, each with an iron nail and a copper strip joined by wires to an LED and a switch. The long, positive leg of the LED goes to the copper strip. In (a) the beaker holds lemon juice. In (b) it holds pure water.switchLEDIronnailCopperstrip(a) Lemon juiceswitchLEDIronnailCopperstrip(b) Pure water
    Fig. 4.12, redrawn.

    Answer

    In case (a), the LED will glow.

    • In (a), the copper strip and the iron nail are two different metals, and lemon juice is an electrolyte. Together they make a cell. Copper is the + electrode, and the LED is joined the right way, so current flows.
    • In (b), pure water is a very poor electrolyte. It hardly lets current pass, so no useful current flows and the LED does not glow.

    One lemon-juice cell gives only a small push. In practice, two or three such cells may be needed in a row to make an LED glow brightly.

  10. Q10
    Neha keeps the coil exactly the same as in Activity 4.4 but slides the iron nail out, leaving only the coiled wire. Will the coil still deflect the compass? If yes, will the deflection be more or less than before?

    Answer

    Yes, the coil will still deflect the compass, because a coil carrying a current has a magnetic field of its own.

    The deflection will be less than before. The iron core was adding its own magnetism. Without it, the electromagnet is weaker.

  11. Q11
    We have four coils, of similar shape and size, made up from iron, copper, aluminium, and nichrome as shown in Fig. 4.13.
    Fig. 4.13 redrawn: four circuits, each with a coil, a cell and an open switch. The coils are made of (a) iron, (b) copper, (c) aluminium and (d) nichrome.+−Iron(a)+−Copper(b)+−Aluminium(c)+−Nichrome(d)
    Fig. 4.13, redrawn.

    When current is passed through the coils, compass needles placed near the coils will show deflection.

    (i) Only in circuit (a)(ii) Only in circuits (a) and (b)(iii) Only in circuits (a), (b), and (c)(iv) In all four circuits

    Answer

    (iv) In all four circuits

    Iron, copper, aluminium and nichrome all conduct electricity. So a current flows in every coil, and every current makes a magnetic field. The magnetic effect does not need a magnetic material for the wire. (The size of the current may differ, because the metals have different resistance.)