Chapter 4 · Science

Electricity: Magnetic and Heating Effects

How an electric current makes a magnetic field, how electromagnets are made and used, why wires get hot and how we use and control that heat, how cells and batteries make electricity, and the symbols used to draw circuits.

Done reading? Try the Electricity lab activity on this chapter.
In this chapter 10 topics
  1. 1Magnetic effect of electric current
  2. 2Electromagnets and their poles
  3. 3Making an electromagnet stronger
  4. 4Uses of electromagnets
  5. 5Heating effect of electric current
  6. 6Heating at work, and heat that is wasted
  7. 7Electrical safety: fuses and MCBs
  8. 8How a cell makes electricity
  9. 9Dry cells, batteries and recharging
  10. 10Circuit symbols and the LED

1Magnetic effect of electric current

Magnetic field

The space around a magnet, or around a wire carrying a current, where its magnetic effect can be felt. A compass needle placed there turns.

Magnetic effect of electric current

A wire carrying an electric current makes a magnetic field around it. The field disappears as soon as the current stops.

The compass test (Activity 4.1)

  1. Stretch a wire between two nails on a piece of cardboard, a little above the board.
  2. Join the wire to a cell and a switch.
  3. Put a compass under the wire. Let the needle settle along the wire.
  4. Switch on and watch the needle. Then switch off.
Two pictures of the same set-up on a piece of cardboard: a cell, a switch and a copper wire stretched over a compass. With the switch off, the compass needle points north, along the wire. With the switch on, current flows and the needle turns away from north.NESW+−Switch OFFNeedle points northNESW+−Switch ONNeedle turns awayswitchcellcompass
Figure 1. A wire over a compass, with the switch off and on.
SwitchCurrent in the wireCompass needle
OFFNoPoints north
ONYesTurns away (deflects)
OFF againNoGoes back to north
  • A compass needle is a tiny magnet. It turns only when a magnetic field acts on it.
  • So a wire with a current in it acts like a magnet.
  • The effect passes through air, paper, plastic and other non-magnetic materials.
  • Reverse the current (turn the cell round). The needle turns the other way.
  • A larger current turns the needle more.
  • A compass can show that current flows, even when there is no bulb in the circuit.

The shape of the field

Left: a straight wire carrying current upwards through a card. The magnetic field lines are circles round the wire. Right: a coil carrying current. Field lines run through the coil and loop round outside, like those of a bar magnet, with a north pole at one end and a south pole at the other.Straight wireCoilCurrentField lines: circlesSNField like a bar magnet
Figure 2. The magnetic field round a straight wire and round a coil.
Wire shapeMagnetic field
Straight wireCircles round the wire. Strongest close to the wire.
Coil of wireLike the field of a bar magnet. One end is a north pole, the other a south pole.

Be a scientist: Hans Christian Oersted (1777 to 1851)

A Danish professor. In 1820, during a lecture, he saw a compass needle move each time a circuit was switched on or off. He tested it carefully, then published his results. Others repeated his test. It showed that electricity and magnetism are linked.

Remember

  • A current-carrying wire has a magnetic field around it.
  • No current, no field.
  • Reverse the current and the needle turns the other way.
  • Oersted found this link in 1820.
Quick checkYou have a cell, a switch, some wire and a compass, but no bulb. How can you tell whether current flows?Show answer

Put the compass under the wire and switch on. If the needle turns, current is flowing.

2Electromagnets and their poles

Electromagnet

A coil of insulated wire that acts as a magnet only while a current flows through it. Most electromagnets have an iron core to make them stronger.

Core

The piece of iron placed inside the coil, such as an iron nail.

Making an electromagnet (Activity 4.2)

  1. Wind about 50 cm of insulated wire tightly round an iron nail. Fix it with tape.
  2. Join the two ends of the wire to a cell. Keep it joined for a few seconds only, or the cell runs down quickly.
  3. Bring the nail near some iron paper clips. They cling to the ends of the nail.
  4. Take a wire off the cell. The clips fall off.
An electromagnet: insulated copper wire wound as a coil round an iron nail. The ends of the wire go to a cell lying on the table. Current flows, and steel paper clips cling to both ends of the nail.+−coil of insulated copper wireiron nail (core)iron clipscell
Figure 3. A simple electromagnet picking up iron paper clips.

With and without an iron core (Activity 4.3)

A coil of about 50 turns is wound on a paper tube. A compass is placed near each end.

Set-upCompass needlesIron clips
Coil, no currentNo changeNot attracted
Coil, current onTurn a littleHardly any
Coil with iron nail, current onTurn a lotMany cling to the ends
Current switched offGo backFall off
  • The coil alone is a weak magnet. The iron core makes it much stronger.
  • The iron core becomes a magnet while the current flows. Its magnetism adds to the coil’s.
  • Soft iron loses its magnetism as soon as the current stops. Steel would stay a little magnetic.
  • The wire must be insulated. Then the current goes round every turn. Bare turns would touch, and the current would take a short cut.

Poles of an electromagnet (Activity 4.4)

  1. Mark the ends of the coil A and B.
  2. Put a compass near end A and switch on.
  3. The north end of the needle is pulled towards A. Unlike poles attract, so A is a south pole.
  4. Repeat at end B. The north end of the needle is pushed away. So B is a north pole.
A coil on an iron nail with ends A and B, joined to a cell. A compass near end A has its red north end pulled towards A, so A is a south pole. A compass near end B has its north end pushed away from B, so B is a north pole.+−NESWNESWABEnd A is SEnd B is Ncell
Figure 4. Finding the poles of an electromagnet with a compass.
  • Like a bar magnet, an electromagnet has two poles: north and south.
  • Reverse the current and the poles swap. A becomes north and B becomes south.

Remember

  • An electromagnet is a magnet only while current flows.
  • An iron core makes it much stronger.
  • It has a north pole and a south pole.
  • Reversing the current swaps the poles.
Quick checkThe north end of a compass needle is pushed away from end B of an electromagnet. Which pole is B?Show answer

North. Like poles repel, so B must be a north pole.

3Making an electromagnet stronger

The strength of an electromagnet means how strongly it pulls iron. We can judge it by the number of clips it lifts, or by how far a nearby compass needle turns.

ChangeEffect on the electromagnet
More turns of wireStronger
More current (more cells in the battery)Stronger
An iron core inside the coilMuch stronger
Reverse the direction of currentSame strength, but the poles swap
Switch off the currentNo longer a magnet
Three electromagnets made from an iron nail, a coil of copper wire and cells. With few turns and one cell it picks up 2 clips. With more turns and one cell it picks up 4 clips. With more turns and two cells it picks up 8 clips. More turns and more current make a stronger electromagnet.Few turns1 cellWeak: 2 clipsMore turns1 cellStronger: 4 clipsMore turns2 cellsStrongest: 8 clips
Figure 5. More turns and more cells make an electromagnet stronger.
  • One cell gives a small current, so the field is weak and only a few clips are lifted.
  • A battery of two or more cells gives a larger current. The field is stronger and more clips are lifted.
  • To test one factor, change only that one. Keep everything else the same. This makes it a fair test.

Electromagnet and permanent magnet

Electro­magnetPermanent magnet
Made ofA coil of wire, often on an iron coreMagnetised steel or a similar material
MagnetismOnly while current flowsAll the time
Switch on and offYesNo
Change its strengthYesNo
Swap the polesYes, by reversing the currentNo
Needs electricityYesNo

A step further: Earth is an electromagnet

Deep inside the Earth, liquid iron moves in the core. This makes electric currents, and they make the Earth’s magnetic field. Many birds, fish and other animals use this field to find their way across continents and oceans. The field also shields life from harmful particles from space.

Remember

  • More turns, more current and an iron core make it stronger.
  • The direction of current decides the poles, not the strength.
  • An electromagnet can be switched on and off. A permanent magnet cannot.
Quick checkGive two ways to make an electromagnet lift more clips.Show answer

Wind more turns of wire on it. Use more cells to pass a larger current. (Using an iron core also helps.)

Try it yourselfSwitch on an electromagnet and change its turns and cells, heat a copper or nichrome wire, and overload a circuit until its fuse melts, in the Electricity lab.

4Uses of electromagnets

Lifting electromagnets

Lifting electromagnet

A very strong electromagnet hung from a crane. It lifts iron and steel when the current is on and drops them when it is off.

Two pictures of a crane in a scrapyard with a lifting electromagnet hanging from its arm. With the current on, scrap iron and steel cling to the magnet and are lifted. With the current off, the magnet lets go and the scrap drops back on to the heap.Current ONCurrent OFFelectro-magnetIron and steel liftedThe load drops
Figure 6. A crane with a lifting electromagnet.
  • The crane operator controls it with a switch.
  • Used in factories and scrap yards to lift, move and sort heavy iron and steel.
  • It also separates iron and steel from other waste. Aluminium, copper and plastic are not lifted.

The electric bell

An electric bell on a wooden board. A battery and a push switch are joined to an electromagnet with two copper coils. Above the electromagnet is a soft iron armature held by a flat spring. A contact screw touches the armature. A hammer on the end of the armature sits close to a brass gong.GongHammerContactscrewSpringSoft ironarmatureElectro-magnetBatteryPush switch
Figure 7. Parts of an electric bell.
  1. Press the switch. The circuit is complete and current flows through the electromagnet.
  2. The electromagnet pulls the soft iron armature down.
  3. The hammer on the armature hits the gong. The bell rings.
  4. The armature has moved away from the contact screw. The circuit breaks and the electromagnet stops working.
  5. The spring pulls the armature back. It touches the screw, and the circuit is complete again.
  6. Steps 2 to 5 repeat many times a second. The bell rings for as long as you press the switch.

More uses

DeviceWhat the electromagnet does
Electric motor (fans, mixers, pumps)Magnetic pushes and pulls make it spin.
Loudspeaker and earphonesIt moves a cone or a thin sheet back and forth to make sound.
RelayA small current works an electromagnet, which switches on a big circuit.
Electric lock and doorbellIt pulls a bolt or a hammer.
MRI scanner in hospitalsA very strong electromagnet helps take pictures of the inside of the body.
Maglev trainPowerful magnets lift the train above the track and push it along.
  • A step further: electricity can make a magnet. A moving magnet can also make an electric current. Power station generators work this way.

Remember

  • Lifting electromagnets: current on, lift; current off, drop.
  • Bell: the electromagnet pulls the armature; the circuit breaks; the spring pulls it back; this repeats.
  • Motors, speakers, relays, MRI and maglev all use electromagnets.
Quick checkWhy is the armature of a bell made of soft iron and not steel?Show answer

Soft iron loses its magnetism as soon as the current stops. So the spring can pull the armature back each time. Steel would stay magnetised and stick.

5Heating effect of electric current

Heating effect of electric current

When a current flows through a conductor, part of the electrical energy changes into heat. So the conductor gets warm or hot.

Resistance

How much a material opposes the flow of current through it. A wire with high resistance gets hotter.

Activity 4.5: does a wire get hot?

  1. Fix two nails about 5 cm apart on a piece of cardboard.
  2. Tie a thin nichrome wire (about 0.3 mm thick, 10 cm long) between them.
  3. Join it to a cell and a switch. Touch the wire with the switch off: it is cool.
  4. Switch on for about 30 s, then off. Touch the wire for a moment: it is warm.
A short nichrome wire stretched between two nails on a piece of cardboard, joined to a cell and a switch. With the switch on, the wire glows red hot and heat rises from it.+−nichrome wire (red hot)cardboardnailcellswitch (ON)
Figure 8. A nichrome wire gets hot when current flows.

Safety. Do this only with a teacher. Touch the wire only for a moment. Never hold it.

Why the wire gets hot

  • Every conductor resists the flow of current a little.
  • Because of this resistance, some electrical energy turns into heat.
  • Nichrome has much higher resistance than copper of the same length and thickness. So it gets much hotter.

What decides how much heat?

FactorMore heat when
CurrentThe current is larger (for example, 2 cells instead of 1)
TimeThe current flows for longer
MaterialThe material has higher resistance (nichrome rather than copper)
ThicknessThe wire is thinner (for the same current)
LengthThe wire is longer (for the same current)

Nichrome

An alloy (a mixture of metals) of nickel and chromium. It is used in heating elements.

  • It has high resistance, so it makes a lot of heat for a given current.
  • It has a high melting point (about 1400 °C), so it can glow red hot without melting.
  • It does not rust or burn away easily when red hot.
  • Connecting wires are made of copper. Copper has low resistance, so it stays cool and wastes little energy.

Common mistake. Nichrome is not an insulator. It conducts electricity, but with high resistance.

Remember

  • Current through a conductor makes heat. This is the heating effect.
  • Heat depends on current, time, material, thickness and length.
  • Nichrome: high resistance, high melting point, does not rust.
  • Copper for connecting wires: low resistance, little heat.
Quick checkWhy are heating elements made of nichrome, while connecting wires are made of copper?Show answer

Nichrome has high resistance and a high melting point, so it gets very hot without melting. Copper has low resistance, so connecting wires stay cool and waste little energy.

6Heating at work, and heat that is wasted

Heating element

A coil or rod of high-resistance wire inside an appliance. It gets hot when current flows. In some appliances you can see it glow red hot.

Six appliances that use the heating effect: a room heater with two red-hot bars, an electric stove with a glowing coil, an electric kettle giving off steam, an electric iron with a hot base, an immersion rod heating a bucket of water, and a hair dryer with a glowing coil inside.Room heaterElectric stoveElectric kettleElectric ironImmersion rodHair dryer
Figure 9. Appliances that use the heating effect.
  • Appliances with a heating element: room heater, electric stove, kettle, iron, immersion rod, hair dryer, toaster and water heater (geyser).
  • Industry: an electric furnace makes great heat. It melts scrap steel so it can be recycled into new steel.

Filament bulb and LED

  • A filament (incandescent) bulb has a very thin coil of tungsten wire. Current makes it white hot, so it glows.
  • Most of its energy becomes heat, not light. This is why such a bulb gets hot to touch.
Left: a filament bulb glowing, with wavy lines of heat around it. Much of its energy is wasted as heat. Right: an LED bulb giving the same bright light with no heat lines. It gives more light for less energy.Filament bulbvery hot: much energywasted as heatLED bulbonly warm: more lightfor less energy
Figure 10. A filament bulb wastes much energy as heat. An LED does not.
Filament bulbLED bulb
How it gives lightA hot wire glowsA tiny electronic part glows
Heat given outA lotVery little
Energy used for the same lightMoreMuch less
LifeShortLong

Unwanted heating

  • Power lines get warm. Some energy is lost as heat on the way from the power station.
  • Chargers, laptops and motors get warm. This heat is wasted energy.
  • Too much heat can melt the plastic of plugs and sockets, and can even cause a fire.
  • So we use wires, plugs and sockets made for the current they will carry.

Remember

  • A heating element is a high-resistance coil that gets hot.
  • A filament bulb glows because its wire is white hot.
  • An LED gives more light for less energy and stays cool.
  • Unwanted heating wastes energy and can cause fires.
Quick checkWhy does an LED bulb save energy compared with a filament bulb?Show answer

A filament bulb turns most of its energy into heat. An LED turns much more of its energy into light, so it needs less energy for the same light.

7Electrical safety: fuses and MCBs

Two faults that cause too much current

Overloading

Using too many appliances on one socket or circuit at the same time. More current flows than the wires are made for, so they overheat.

Short circuit

When the live and neutral wires touch directly, often because the insulation is damaged. The current takes a short cut with almost no resistance, so a very large current flows.

Left, overloading: a heater, an iron and a kettle all plugged into one socket through an adapter. The cable gets red hot and gives off heat. Right, a short circuit: the insulation on the live and neutral wires has worn away and the bare copper wires touch, making a spark.heaterironkettlehot cableOverloadingToo many appliances at onceShort circuitlive wireneutral wirebare wires touch:a spark!Huge current, sparks, fire
Figure 11. Overloading and a short circuit.

The fuse

Fuse

A safety device with a short, thin wire that melts easily. If the current becomes too large, the wire heats up, melts and breaks the circuit.

  1. The fuse is joined in the circuit, so all the current passes through its wire.
  2. With normal current, the fuse wire stays cool enough and does not melt.
  3. With too much current, the fuse wire heats up quickly and melts.
  4. The circuit breaks. Current stops before the wiring can overheat and start a fire.
  • Every fuse has a rating. This is the largest current it can carry safely, such as 5 A or 13 A. (A stands for ampere, the unit of current.)
  • A melted fuse must be replaced by one of the same rating, after the fault is found and fixed.
  • Never use a thicker wire, a nail or a piece of foil in place of a fuse. It would not melt, and the wires could catch fire.
  • In circuit diagrams a fuse is shown as a small box on the wire (see Figure 17).

The MCB

MCB (miniature circuit breaker)

An automatic switch that turns off by itself when the current is too large. It is reset by pushing its lever back up.

Three pictures. First, a fuse carrier with its thin fuse wire whole, and a lamp in the circuit glowing. Second, too much current: the fuse wire has melted and broken, leaving a scorch mark, and the lamp is off. Third, a miniature circuit breaker whose lever has dropped to OFF; pushing it up resets it.ONOFFNormalcurrentFuse wire whole.Lamp works.Too muchcurrentFuse wire melts.Circuit breaks.MCBtripsLever drops.Push up to reset.
Figure 12. A fuse melts when the current is too large. An MCB switches off.
FuseMCB
What happensThe wire meltsA switch trips to OFF
After a faultMust be replacedReset by pushing the lever up
Uses which effectHeating effectHeating effect, magnetic effect, or both

Safety rules

  • Do not plug too many appliances into one socket.
  • Use wires, plugs and sockets made for the current they will carry.
  • Buy appliances and wires with a standard safety mark from your country’s standards body.
  • Replace wires with damaged insulation at once.
  • Never touch switches or appliances with wet hands. Switch off before cleaning an appliance.

Remember

  • Overloading and short circuits cause too much current.
  • A fuse wire melts and breaks the circuit when the current is too large.
  • Replace a fuse only with one of the same rating.
  • An MCB switches off by itself and is reset by hand.
Quick checkWhat could happen if a melted fuse wire is replaced with a thick copper wire?Show answer

The thick wire would not melt when the current became too large. The circuit would not break, so the wiring could overheat and cause a fire.

8How a cell makes electricity

Electric cell

A device that makes an electric current from chemical reactions inside it.

Electrode

Each of the two metal rods or plates in a cell. They must be of two different metals.

Electrolyte

The liquid or paste between the electrodes. It is usually a weak acid or a salt solution. It lets current pass inside the cell.

The Voltaic cell

  • One of the first cells ever made. It is also called a Galvanic cell.
  • Two rods of different metals (for example copper and zinc) stand in an electrolyte in a glass or plastic container.
  • A chemical reaction between the rods and the electrolyte makes electricity.
  • In the outside circuit, current flows from the positive (+) terminal to the negative (−) terminal.
  • Over time the chemicals get used up. The cell stops working and is called “dead”.
A Voltaic cell: a copper rod and a zinc rod dipped in an electrolyte in a glass beaker. Wires with crocodile clips go from the rods to a lamp, which glows. Current flows out of the copper rod, the positive electrode, through the lamp and back into the zinc rod, the negative electrode.+−Copperrod (+)Zincrod (−)Electrolyte(weak acid orsalt solution)Lamp glowscurrent
Figure 13. A simple Voltaic cell lighting a lamp.

Ever heard of: Galvani and Volta

In the late 1700s, the Italian scientist Luigi Galvani saw a dead frog’s leg twitch when it touched copper and iron. He thought the electricity came from the frog. Alessandro Volta disagreed. He used paper soaked in salt water instead of the frog’s leg and still got a current. So the electricity came from the two metals and the liquid. This led to the first battery.

A lemon cell (Activity 4.6)

  1. Push a copper wire and an iron nail into a lemon, a little apart.
  2. Do the same with four or five more lemons.
  3. Join the iron nail of each lemon to the copper wire of the next.
  4. Join an LED between the copper wire of the first lemon and the nail of the last lemon.
  5. The LED glows. If it does not, turn the LED round.
Four lemons on a table, each with a copper wire and an iron nail pushed in. The nail of each lemon is joined to the copper wire of the next. The copper wire of the first lemon goes to the long, positive leg of an LED and the nail of the last lemon goes to its short, negative leg. The LED glows.+ (long leg)− (short leg)LED glowscopper wire (+)iron nail (−)lemon juice
Figure 14. Lemons joined in a row light an LED.
Part of a cellIn the lemon cell
Positive electrode (+)Copper wire
Negative electrode (−)Iron nail
ElectrolyteLemon juice
  • One lemon gives too little push to light an LED. So several lemons are joined.
  • A salt solution can be used in place of lemon juice. Pure water is a very poor electrolyte, so it does not work well.
  • Other metal pairs that work: zinc and copper, zinc and silver, aluminium and copper, magnesium and copper, lead and copper.
  • Copper usually acts as the positive electrode. Zinc usually acts as the negative one.

Remember

  • A cell turns chemical energy into electrical energy.
  • A cell needs two different metals and an electrolyte.
  • Current flows from + to − through the outside circuit.
  • Volta made the first battery.
Quick checkIn a lemon cell, which part is the electrolyte and which are the electrodes?Show answer

The lemon juice is the electrolyte. The copper wire and the iron nail are the electrodes.

9Dry cells, batteries and recharging

The dry cell

  • The most common cell in torches, clocks and remotes.
  • It is called “dry” because the electrolyte is a thick, moist paste, not a liquid. So it does not spill and is easy to carry.
A dry cell seen from outside, with + at the capped top and − at the bottom, and cut open. Inside, a black carbon rod with a metal cap (the positive terminal) stands in the middle of a dark moist paste (the electrolyte). Everything is held in a zinc case, which is the negative terminal.+1.5 V−OutsideInsideMetal cap (+)Carbon rodMoist paste(electrolyte)Zinc case (−)
Figure 15. A dry cell, outside and cut open.
PartJob
Carbon rod with a metal cap, in the centrePositive terminal (+)
Moist paste round the rodElectrolyte
Zinc containerNegative terminal (−)
  • A dry cell is used only once. When it is used up, it must be thrown away safely.

Cells and batteries

Battery

Two or more cells joined together. In everyday speech, a single cell is often called a battery too.

Three cells placed end to end in a holder, the + end of each touching the − end of the next, form a battery of 3 cells. Below are the circuit symbols for one cell and for a battery of 3 cells.Cells joined + to − make a battery+−+−+−A battery of 3 cellsSymbols+−Cell+−Battery of 3 cells
Figure 16. Cells joined + to − make a battery.
  • To join cells in a row, the + end of one cell touches the − end of the next.
  • More cells give a bigger push, so more current flows in the same circuit.
  • A bulb glows brighter, an electromagnet gets stronger, and a wire gets hotter.

Rechargeable batteries

Rechargeable battery

A battery that can be charged again and used many times. Charging drives the chemical reaction backwards.

TypeUsed in
Lithium-ion (Li-ion)Phones, laptops, tablets, cameras, electric vehicles
Lead-acidInverters, cars and motorbikes
Nickel-metal hydrideRechargeable AA and AAA cells, toys
  • They save money and reduce waste.
  • They do not last forever. After many charges they slowly wear out. A phone battery needs charging more often after a year or two.
  • Li-ion batteries use metals such as lithium and cobalt. These are mined in only a few parts of the world. So recycling old batteries matters.
  • Scientists are making solid-state batteries. They use a solid electrolyte. They should be safer, charge faster and last longer.

Is a cell dead?

  • A bulb or LED joined to it does not glow, or a toy does not work.
  • A compass under a wire joined to it does not turn.

Safe disposal

  • A “dead” battery still holds acids and metals such as lead, cadmium, nickel or lithium.
  • In ordinary rubbish they can cause fires and pollute soil and water.
  • Take used batteries to an e-waste collection point, where they are recycled. Never burn them or break them open.

Remember

  • Dry cell: zinc case (−), carbon rod (+), moist paste electrolyte.
  • A battery is two or more cells joined + to −.
  • Rechargeable batteries can be reused many times but wear out slowly.
  • Used batteries are e-waste. Recycle them.
Quick checkWhy is a dry cell more useful for a torch than a Voltaic cell?Show answer

Its electrolyte is a paste, so it does not spill. It is small, light and easy to carry.

10Circuit symbols and the LED

Circuit diagram

A simple drawing of a circuit that uses symbols for its parts. Wires are drawn as straight lines.

Circuit symbols in nine coloured cards: a cell (long line +, short thick line −), a battery of two cells, an open switch, a closed switch, an electric bulb (a circle with a cross), an LED (a triangle pointing to a bar, with two arrows for light, + on the left), a fuse (a box on the wire), a resistor or heating wire (a zigzag) and joined wires (a dot where they meet).+−Cell+−BatterySwitch: open (OFF)Switch: closed (ON)Electric bulb+−LEDFuseResistorJoined wires
Figure 17. Common circuit symbols.
PartHow its symbol looks
CellA long thin line (+) and a short thick line (−)
BatteryTwo or more cell symbols joined in a row
SwitchA break in the wire with a lever: open is OFF, closed is ON
Electric bulbA circle with a cross inside
LEDA triangle pointing at a bar, with two small arrows for light
FuseA small box with the wire running through it
Resistor or heating wireA zigzag line
Joined wiresA dot where the wires meet

The LED

LED (light emitting diode)

A small lamp that lets current flow through it in one direction only.

Left: an LED: a coloured plastic dome with two metal legs. The longer leg is positive and the shorter leg is negative. Right: two circuits with a cell and an LED. When the + side of the cell is joined to the + leg of the LED, current flows and it glows. With the cell reversed, it does not glow.An LED+−longer leg: +shorter leg: −colouredplastic domeLED in a circuit+−Glowsright way round+−No glowcell reversed
Figure 18. An LED glows only when it is joined the right way round.
  • The longer leg is positive (+). The shorter leg is negative (−).
  • Join the + leg towards the + terminal of the cell, and the − leg towards the − terminal.
  • Joined the wrong way, the LED does not glow. Turn it round.
  • In the symbol, the triangle points the way the current flows.
  • LEDs use little energy and stay cool.

Remember

  • Long line of the cell symbol = +.
  • Open switch: no current. Closed switch: current flows.
  • LED: longer leg +, works one way only.
Quick checkAn LED in a circuit does not glow. Give two possible reasons.Show answer

The LED may be joined the wrong way round. The cell may be dead, or a wire may be loose.

Test yourselfTake the 16-question practice quiz on this chapter.